Drill Bits

  •
    Quick View

    Makita 18-Pc Assorted Drill Bit Set

    Get the right bits for your driver-drill or hammer driver-drill. The 18 Pc. Assorted Drill Bit Set (D-59178) offers an assortment of straight shank bits for use in metal, wood, and masonry materials. The metal drilling bits are made of HSS-G for longer life with a 135-degree split-point geometry for fast starts and reduced “walking”. The brad point wood drill bits are engineered for clean, straight holes in wood, and the masonry hammer drill bits can be used in most hammer drills for use in brick, block, and concrete. The straight shank bits are for use with most corded and cordless ⅜” and ½” drills.

  •
    Quick View

    Euroboor Cobalt 29 Pc Index Jobber Set

    The Euroboor M35 Cobalt High Speed Steel Jobber drill set is ideal for drilling through cast iron and stainless steel. The 135° split point helps to eliminate tip walking, and increases hole accuracy. The unique flute design is superior for removing shavings and material from the hole. All bits above 3/16″ have a 3-flat shank for stability in any drill or chuck.

  •
    Quick View

    URREA Metal Bit Box, 1/16″ Increments

    Bit boxes allow you to conveniently transport your bits without damaging or losing them. This bit box is used for storing 29 bits inthe following sizes: 1/16″ to 1/2″, in 1/64″ increments.

  •
    Quick View

    Makita 1-1/8″ X 18″ Ship Auger Drill Bit

    This ship auger drill bit by Makita has a cutting edge to quickly cut through wood with maximum efficiency. Its thick edge quickly and easily cuts through nails, and its screw point pulls the bit through material for faster drilling. The wide flutes allow for faster chip removal as well, to improve function and speed even more.

  •
    Quick View

    Makita Impact Gold 14 Pc Titanium Drill Bit Set

    The Impact GOLD® 14 Pc. Titanium Drill Bit Set (B-65399) offers an assortment of ¼” hex shank bits for drilling clean and accurate holes in metal, wood and plastic.
    With the Titanium Nitride (TiN) coating, these bits are engineered to last 2.5X longer than non-coated bits. The 135-degree split-point geometry is built for fast starts and reduced “walking”. The bits are impact-rated and for use in ¼” hex impact drivers .
    They are ideal for drilling holes in ferrous metal, wood, plastic, non-ferrous metal, cast iron and stainless steel.

  •
    Read More
    Quick View

    Makita HSS Drill Bit Black Oxide 1/4″ Drive

    Broken drill bits are a waste of time. Makita Black Oxide Drill Bits are designed for use with today’s high-torque drills and impact drivers, and engineered for added durability for longer service life. The durable one-piece design is constructed with High Speed Steel (HSS), with a ¼” hex shank for use with impact drivers and driver-drills. Makita Black Oxide Drill Bits are ideal for drilling holes in ferrous metal, wood, plastic, non-ferrous metal, and cast iron.

  •
    Read More
    Quick View

    Pilot Drill Bits for Hole Saw Arbors

    As you use your hole saw blades, the pilot bit in the arbor will eventually wear out. Rather than buying a full replacement arbor, you can just buy a new pilot bit and replace the old bit.
    These pilot bits are made from High Speed Steel (HSS), and fit all hole saw arbors. They are available in lengths of 3″ and 4″. There is even a carbide tipped 4″ bit available if you need extra cutting power.

  •
    Read More
    Quick View

    Arbors for Hole Saws, Mag-Bit

    These arbors attach to various sizes of hole saws, and have shanks for hex and SDS drivers. They are made by Mag-Bit, but match industry standard hole saws. Each arbor can attach to multiple sizes of hole saw, with the smallest starting at 9/16″ and going up to 1-3/16″.
    The larger size starts at 1-1/4″, and runs up to the largest at 6″. This size has two posts that fit into matching holes in the back plate of the saw body, so ensure that the saw can’t spin around the arbor as you cut the hole.
    In addition to that choice, an arbor may have a shank that is 1/4″, 3/8″, or 7/16″ hex, or SDS.

  •
    Read More
    Quick View

    Ship Auger Drill Bits

    High quality ship auger bits that are machined on a true center. They have a quick-change hex shank, and a self-feeding screw point.

    Available sizes are 6″ length in diameters from 1/2″ to 1-1/2″, and 12″ length from 1/4″ to 1-1/2″, in 1/16″ increments below 1″, and 1/8″ increments above 1″. 

  •
    Quick View

    Silver & Deming Drill Bit Set, 8 Pc

    ALFA Tools SD50449PL 8 pc 9/16-1″ USA Silver & Deming Set
    Alfa USA Silver Deming 8 Piece Drill Set in Molded Plastic Case
    Sizes 9/16″ to 1″ by 1/16th increments
    High Speed Steel
    Black Oxide Finish
    118 degree Point
    1/2 Reduced Shank
    3 Flats
    Right Hand Spiral
    Made in USA

  •
    Read More
    Quick View

    Silver & Deming, 1/2″ Shank

    Made especially for drill presses and milling machines, these Silver & Deming drill bits are 6″ long with a 3″ drilling depth. They all have a 1/2″ shaft.

  •
    Read More
    Quick View

    Paddle Bits, Individual

    Paddle bits, also called spade bits, have a wide, flat blade. They are commonly used by tradesmen such as electricians and plumbers for drilling holes through studs in walls for running wiring or pipes (auger bits and hole saws are also used for this), but they also have a place in the woodshop for drilling on fine woodworking projects.
    An extension kit is available for the extreme jobs. It includes a 12″ extension shaft, and a bent-hex tool to securely tighten the retaining screws when the paddle bit is installed. (See image.)