STI BIOSTOP 1-1/2″ Fire Rated Pipe Collar
Pipe Collars are prefabricated for open and closed through-penetration firestop systems using 1 1/2″(38 mm) to 6″ (152 mm) plastic pipe. An easy locking tab assures easy installation. The collar design greatly reduces the time and expense that is required to install competitive collars.
- Description
- Properties
- Data Sheets & Downloads
Biostop® Pipe Collars are used to seal off plastic pipe both in closed and vented (DWV) conditions. Also for use on up to 6" (152 mm) diameter id core), FRPP, PVC and CPVC pipe. The collar may be used on up to 3 hour rated concrete floors and walls, up to 2 hour rated gypsum walls and up to 2 hour rated wood floors.
- Saves on Labor Cost
- Easy Installation
- Economical
- No Measurement of Material Required
- Highly Intumescent
- Tested for PVC, CPVC, ABS and PVC/ABS Foam Core, FRPP
Related Products
-
Read MoreQuick ViewSpecSeal LCC Firestop Collar Series
The SpecSeal® LCC Collar is a factory-manufactured device designed to protect plastic pipes penetrating fire-rated walls and floors. Utilizing a heavy gauge galvanized metal collar to house a molded intumescent insert, the SpecSeal® LCC Firestop Collar is specifically sized to fit 1-1/2 in, 2 in, 3 in, and 4 in (38 mm, 51 mm, 76 mm and 102 mm) trade sized pipes. When exposed to temperatures in excess of 320°F (160°C), the SpecSeal® LCC Collar’s molded insert begins to expand (intumesce) rapidly to form a dense, highly insulative char. Its free expansion ranges from 32x to 64x original (pre-expanded) volume. Expansion continues up to 1,000°F (538°C).
-
Quick ViewFirestop Closet Toilet Flange Gasket
SpecSeal Closet Flange Firestop Gaskets are one-piece, molded rubber, intumescent pads that install beneath a 3″ (76 mm) or 4″ (102 mm) closet flange to effectively firestop the opening. The die cut rubber gasket is perforated to delineate removable inserts sized to accommodate various outer diameters of toilet flanges.
-
Read MoreQuick ViewSpecSeal SSW Wrap Strip, Pre-Cut or 12 Ft Roll
-
Read MoreQuick ViewSpecSeal Putty Tube or Pad
SSP Putty & Putty Pads
SpecSeal SSP Firestop Putty excels at sealing cabling penetrations and outlet boxes. SSP Putty is non-hardening and easily hand works around grouped cabling penetrations forming a re-enterable seal allowing for future work. When applied with outlet boxes, SSP Putty easily works into voids and seams forming a continuous seal against fire and the products of combustion. -
Quick ViewBIO Firestop Pillow 3″ X 9″ X 6″
Intumescent Firestop Pillows are designed for use primarily in large openings with cables, cable trays, blank openings or multiple penetrating items. In the event of a fire, BIO™ Firestop Pillows will prevent the spread of flames and hot gases through the openings. Since no cure time is required, BIO™ Firestop Pillows are ready to install. BIO™ Firestop Pillows are reusable since they can be removed and reinstalled if necessary.
-
Read MoreQuick ViewSpecSeal SSB Firestop Pillows
SpecSeal SSB Firestop Pillows consist of a mineral fiber core material sealed with a water-resistant intumescent membrane. This coated core material is then heat-sealed in a tough, nonirritating, fireretardant poly bag. They easily compress and conform around any penetrant. Equally suited for new or existing conditions, SpecSeal Pillows make short work of even the most complex through-penetration firestop conditions.
-
Quick ViewFire Safing 4″ X 24″ X 48″ , 4 Panels
Mineral Wool Fire Safing is designed to provide enhanced fire protection in perimeter fire containment systems, floor and wall penetrations, construction joints, and other firestopping applications. It is non-combustible, moisture-resistant, non-corrosive, non-deteriorating, mildew-resistant and vermin-resistant. Mineral Wool FireStop Safing is primarily used as a backing material for firestop caulks and sealants.
-
Quick ViewSpecSeal FS200 2″ Ready Sleeve
SpecSeal Ready Sleeves are designed for new cabling penetrations where sleeves are required. Each Ready Sleeve kit includes a preformed steel sleeve with rolled edges, steel escutcheon plates with intumescent gaskets, and a dosage of our SpecSeal SSP Firestop Putty. The rolled edges of each Ready Sleeve eliminate the need for bushings while the included escutcheon plates and gaskets take the place of steel strut and strap supports.
SpecSeal® Ready® Sleeve Pathways are used to protect or support cables in both nonrated and rated construction. SpecSeal® Ready® Sleeve Pathways are suitable for use in all common constructions including concrete floors, concrete walls, concrete block walls, and gypsum board/stud wall assemblies up to 10” (254 mm) thick. -
Read MoreQuick ViewSpecSeal Cast In Place Device
Eliminate core-drilling and firestop after the concrete pour with SpecSeal CID Cast-In Firestop Devices. SpecSeal Cast-In Devices are a sleeve, concrete form and firestop rolled into a single device. SpecSeal Cast-In Devices are available in a range of sizes and heights to accommodate penetrant up to 6″ Trade Size penetrants and concrete depths of up to 36″.
-
Quick ViewSPEC SEAL EZD22 EZ-PATH FIRE RATED PATHWAY
The EZ Path® Series 22 Fire Rated Pathway is a maintenance-free pathway device designed to allow cables to penetrate fire-rated walls without the need for firestopping. This device features a built-in fire sealing system that automatically adjusts to the amount of cables installed. Once installed in a fire barrier, cables can be easily added or removed at any time without the need to remove or reinstall firestopping materials.
