Anchors

  •
    Read More
    Quick View

    Toggle Bolt, Zinc Plated

    The Toggle Bolt is a spring wing type hollow wall anchor designed for use in block, wallboard and other hollow base materials. The Toggle Bolt is a two-part assembly consisting of a machine screw and a spring wing toggle. Sizes range from 1/8″ x 2″ to 1/2″ x 6″ with combo round, flat, mushroom, tie-wire or slotted hex head styles.

  •
    Read More
    Quick View

    Anchor Setting Tool Powder Load Strips

    Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These color coordinated .25  and .27 caliber powder loads provide the force needed to drive those fasteners into place. They provide from medium power up to the highest power of loads available.
    Each strip has 10 powder loads, and there are 10 strips per box.
    Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator’s manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders.

  •
    Read More
    Quick View

    Plastic Anchor Kit

    This kit contains standard drywall/concrete expansion anchors, screws, and a masonry drill bit sized appropriately.
    Kits are available with standard Phillips pan head screws, or with slotted hex head washer screws. 
    Sizes are:
    3/16″ Anchor & Bit, with #6 – #8 x 3/4″ Phillips Pan Head Screw
    1/4″ Anchor & Bit, with #10 – #12 x 1″ Phillips Pan Head Screw
    1/4″ Anchor & Bit, with #10 – #12 x 1″ Slot Hex Head Screw

  •
    Read More
    Quick View

    Grey Plastic Anchor, w/Lip

    This is a standard plastic expansion anchor that can be used in drywall or solid walls for light hanging or attaching needs.

  •
    Read More
    Quick View

    Grey Plastic Anchor, No Lip

    This is a standard plastic expansion anchor that can be used in drywall or solid walls for light hanging or attaching needs. This type has no outer ring or lip that remains outside the pre-drilled hole, so there will not be any plastic visible once the screw is in place. Also, whatever is being attached to the wall will sit directly against the wall, with no gap.

  •
    Read More
    Quick View

    Blue Plastic Anchor, w/Lip

    This is a standard plastic expansion anchor that can be used in drywall or solid walls for light hanging or attaching needs.

  •
    Read More
    Quick View

    Anchor Setting Tool Powder Load, .22 Caliber

    Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .22 caliber powder loads provide the force needed to drive those fasteners into place. This level is the lightest available, for smaller fasteners and thinner materials.
    Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders.

  •
    Read More
    Quick View

    Lead Wood Screw Anchor

    Lead wood screw anchors, also known as lead wood screw shields, are ideally suited for projects that require fastening wood or anchoring brick, concrete, block or softer masonry. You’ll find these anchors install easily as the lead alloy material is soft enough to use, yet hard enough to provide strong holding power. A pre-drilled hole is required for installation.
    We do not recommend for ceiling applications. 

  •
    Read More
    Quick View

    Lag Shield, Long and Short

    The Lag Shield is a screw style anchor designed for use with lag bolts. It is suitable for use in concrete and the mortar joints of block or brick walls. In harder masonry materials, short style Lag Shields are used to reduce drilling time. The long style version is used in soft or weak masonry to better develop strength. The Lag Shield is not recommended for overhead or life safety applications.

  •
    Quick View

    1/2″ Combo Bit for 1/4″ Lead M/S Anchor

    This 1/2″ combo drill bit installs lead anchors for 1/4″-20 combo sidewalk bolts. I works for all masonry surfaces, both block and concrete. The smaller pilot bit starts the hole in the right location, and the larger 1/2″ step bit drills the perfect hole for setting lead machine screw anchors.
    Fully adjustable collar allows you to set the depth of the hole for a perfect set every-time. Comes with Hex Wrench.

  •
    Read More
    Quick View

    Lead Machine Screw Anchor

    The lead machine screw anchor is an internally threaded anchor designed to make female threads into concrete. It features a soft lead shell on the outside and steel threads on the inside. They are designed for solid concrete but can be installed into hollow block or brick with a special setting tool.

  •
    Read More
    Quick View

    Hollow Wall Anchor, Long and Short

    The sleeve type hollow wall anchor is designed for use in base materials such as plaster, wallboard, concrete block, hollow tile or plywood. It is installed using a drill and can be used with various wall thicknesses. The sections of the sleeve expand as the screw is tightened and driven into the wall. The front section of the hollow wall anchor will add permanent screw threads, so that once set, the screw may be removed as often as necessary without affecting the anchor.
    These anchors are also known as Molly bolts.