Sidewalk Bolt, Stainless Steel
Also known as shutter screws, the ultra-wide truss head distributes the load over a large area for excellent holding pressure when placing plywood, metal, and fabric hurricane panels or removable track. Made of 18-8 stainless steel, these screws are chemical resistant and may be mildly magnetic.
- Additional information
- Description
Additional information
| Size | 1/4″-20 x 1/2″, 1/4″-20 x 3/4″, 1/4″-20 x 1″, 1/4″-20 x 1-1/4″, 1/4″-20 x 1-1/2″, 1/4″-20 x 2″, 1/4″-20 x 2-1/2″, 1/4″-20 x 3″ |
|---|
Also known as shutter screws, the ultra-wide truss head distributes the load over a large area for excellent holding pressure when placing plywood, metal, and fabric hurricane panels or removable track. Made of 18-8 stainless steel, these screws are chemical resistant and may be mildly magnetic.
Related Products
-
Quick ViewRamset T3 Fuel Cell, 2-Pack
All fuel cells replace conventional powder loads and drive more than 1000 shots.
-
Hot
Quick ViewHex Head Cap Screws – Stainless
Hex Head Cap Screws are designed for easy assembly into a tapped hole. Stainless Steel Hex Cap Screws meet SAE and ASTM F593 specifications with a specially designed washer face under the head and a chamfered point.
-
Read MoreQuick ViewAnchor Bolts, L-Bolts
-
Quick ViewElite Clevis Hanger
A clevis hanger consists of one U-shaped clevis and a second V-shaped clevis with a hole in a flattened section at the base of the V, joined together with a bolt. Clevis hangers are used as a pipe attachment providing vertical adjustment for pipes
-
Read MoreQuick ViewT-Nuts
T-nuts are barrel shaped fasteners with internal threading, and are used to provide an anchor point for a bolt in a piece of wood, whether a flat board or a dimensional piece. They are especially useful when a flush surface is wanted. T-nuts have a flat base with prongs bent up at 90° angles, parallel to the barrel. After pre-drilling a hole, the t-nut can be fixed in place either by tightening a bolt into it from the top, which pulls the prongs into the wood, or using hammer to pound the locking prongs into the wood until flush.
-
Read MoreQuick ViewPOWER-Skru Bolt Anchors
The POWER-Skru Bolt Anchor is a high-strength screw anchorwith self-taping threads that offer a unique undercutting design for anchoring into concrete and masonry. No secondary setting is needed. The POWER-Skru Bolt Anchor provides high-strength performance with low installation torque. A heavy-duty mechanically-galvanized finish is available to enhance corrosion resistance.
Can be used with almost any material, including:
- Racking
- Railing Sill
- Stadium Seating
- Tilt up Braces
- Formwork
- Anchoring Equipment
-
Hot
Quick ViewHex Head Cap Screws – Grade 2
Hex Head Cap Screws are designed for easy assembly into a tapped hole. Hex Cap Screws meet SAE specifications with a specially designed washer face under the head and a chamfered point. Plain finish, or bare metal, will have a coating of light oil to resist corrosion. Grade 2 is generally an economical but lower strength fastener.
-
Quick ViewPanelMate Quick Kit
This kit contains all of the hardware you need to get started making your home hurricane-resistant. There are 40 PanelMate anchors, along with the bit and driver to properly set them. There are also 40 washers and wing nuts to secure the storm panels to the anchors.
-
Read MoreQuick ViewCarriage Bolts
Carriage bolts have a smooth rounded head with a square neck underneath that locks into wood to prevent spinning when tightened. Use with a pre-drilled hole and secure with a hex nut and washer. They are great fasteners for decks, play equipment, docks, fencing, and furniture.
The unique design is great for connections where the head is not accessible for tightening. The self-locking square neck and coarse threads fasten very securely.
All carriage bolts we stock have coarse threading as a standard. -
Quick ViewPAM #8 X 2-1/2″ Roof Tile Screws
Stainless steel tile roofing screws for use with the PAM auto-feed screw system. These screws are #8 x 2-1/2″ and used for attaching roof tile to wood. The type 17 point improves penetration of tile.
Meets Miami-Dade County, FL Protocol PA 114-95, Appendix E, Section 2 (ASTM G85). Box of 1,000 screws.
