Twirl Nut, 3/8″-16
Twirl nut, 3/8″-16, for use with strut.
- Description
Twirl nut, 3/8"-16, for use with strut.
Related Products
-
U-Bolt Style Beam to Channel Clamp
The U-Bolt style beam-to-channel clamp features a piece of bent plate and a u-bolt that is threaded on both sides to secure a strut in place against a beam. The strut is fed through the u-bolt, which is then tightened to secure both the plate to the beam and the strut to the plate. U-style beam clamps can be used to secure strut to either the underside of the beam or the inside of the beam, depending on the configuration of the clamp.
-
3-Hole Corner Angle L Bracket
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 2-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
2-Hole Closed 45 Degree Angle Connector
This connector is used for connecting metal struts together, at a 45° angle. The two sides are 3-1/2″ and 2-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Read MoreQuick View
Gasket, Ring, Red Rubber
These gaskets are comprised of red rubber, a copolymer of Styrene and Butadiene, also known as SBR. It feature excellent impact and tensile strength, good resistance to abrasion and easily conforms to uneven flange surfaces.
This Synthetic material was developed as an alternative to Natural Rubber. The red rubber gaskets are recommended for service in cold and hot water, air, steam,and some weak acids. It should not be used with strong acids, oils, grease, and chlorates -
4-Hole Corner Angle L Bracket, Stainless
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 4-1/8″ long, with three 9/16″ holes to secure to struts or other surfaces. Stainless steel material makes this product more rust resistant, and it is suitable for exterior uses where rain or salt water are expected.
-
Read MoreQuick View
Concrete Forms, Econ-O-Sleeve
Econ-O-Sleeve Hole Forms consistently form round, smooth, uniform holes and are available in a broad range of diameters. They may be cut, stacked, or telescoped for any slab thickness.
Form holes, don’t drill em!
Econ-O-Sleeve forms come in a variety of diameters, and adjust for any slab thickness by stacking two or more together. -
2-Hole Corner Angle L Bracket A
This connector is used for connecting metal struts together, as a 90° angle. The two sides are 2-1/4″ and 1-5/8″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Elite Clevis Hanger
A clevis hanger consists of one U-shaped clevis and a second V-shaped clevis with a hole in a flattened section at the base of the V, joined together with a bolt. Clevis hangers are used as a pipe attachment providing vertical adjustment for pipes
-
Read MoreQuick View
Caddy 1-Hole Strap for Conduit
The CPVC One Hole Wrap Around Pipe Strap is designed to support pipe running horizontally on side of a beam, or as a guide to mount CPVC pipe running perpendicular across the top of a beam, or on a vertical run. Model 1070 may be installed onto wood using supplied fastener, or into minimum 20 gauge steel using one 1/4″ x 1 tek screw.
-
Standard Riser Clamps (6400)
Model 6400 Standard Riser Clamps from Elite components are designed for copper tube sizes. They are available in carbon steel with Copper colored Epoxy (PC) and in sizes from 1/2″ thru 4″.Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8)