3-Hole Corner Angle L Bracket
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 2-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
- Description
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2" and 2-1/2" long, with a 9/16" hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
Related Products
-
Read MoreQuick ViewPost Bases for 1-5/8″ Strut
These three models of a post base provide a secure mounting point for strut. Once properly bolted in place, it is guaranteed not to move. And with six bolt holes on three sides for all models, the strut will be held in place with no chance of slipping out.
Options include having a square base plate, held in place with four bolts (10 hole models), or a smaller rectangular base held down by two bolts (8 hole model). In addition, the 10 hole model can have the strut and plate square to each other, or having the plate at a 45° angle. These various configurations are meant to accommodate your specific needs. -
Quick View8-Hole Strut Wing Corner Connector
This connector is used for connecting metal struts together, with the ends of two against a third strut between them. An electro-galvanized coating provides rust resistance.
-
Quick View
2-Hole Corner Angle L Bracket B
This connector is used for connecting metal struts together, as a 90° angle. The two sides are 2″ and 1-7/8″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance. -
Read MoreQuick View
Gasket, Ring, Red Rubber
These gaskets are comprised of red rubber, a copolymer of Styrene and Butadiene, also known as SBR. It feature excellent impact and tensile strength, good resistance to abrasion and easily conforms to uneven flange surfaces.
This Synthetic material was developed as an alternative to Natural Rubber. The red rubber gaskets are recommended for service in cold and hot water, air, steam,and some weak acids. It should not be used with strong acids, oils, grease, and chlorates -
Quick View
Elite Beam Clamp
Elite Beam Clamps are used as structural attachments to the top or bottom of metal beams, purlins, channel, or angle iron.
-
Quick View
Purlin Clamp, 3/8″
Purlin clamps provide structural attachment specifically to the purlins that support a roof. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room.
-
Quick View
4-Hole Corner Angle L Bracket
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 4-1/8″ and 3-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Read MoreQuick View
Caddy 1-Hole Strap for Conduit
The CPVC One Hole Wrap Around Pipe Strap is designed to support pipe running horizontally on side of a beam, or as a guide to mount CPVC pipe running perpendicular across the top of a beam, or on a vertical run. Model 1070 may be installed onto wood using supplied fastener, or into minimum 20 gauge steel using one 1/4″ x 1 tek screw.
-
Quick View
Wide Beam Clamp, Galvanized, Shiny
Beam clamps provide structural attachment to the flange of metal beams, purlins, channel strut, or angle iron. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room. With its galvanized coating, this clamp can also be used in exterior or open building situations.
-
Read MoreQuick View
Junior Beam Clamp, Plain
Beam clamps provide structural attachment to the flange of metal beams, purlins, channel strut, or angle iron. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room.
