Ramset Washer Pin Fastening Systems
Designed to drive flush into steel and concrete
Consistent and optimum quality in every pin
Washer increases bearing surface against material
- Additional information
- Description
Additional information
| Size | 3/4″, 1″, 1-1/4″, 1-1/2″, 2″, 2-1/2″, 3″ |
|---|
Designed to drive flush into steel and concrete
Consistent and optimum quality in every pin
Washer increases bearing surface against material
Related Products
-
Quick View1-1/4″ Ceiling Clip Assembly
The Ramset Ceiling Clip is designed to mount into a slanted ceiling, with hanging wire attached through the eye. Able to support light loads such as suspended ceiling grids.
-
Read MoreQuick ViewAnchor Setting Tool Powder Load Strips
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These color coordinated .25 and .27 caliber powder loads provide the force needed to drive those fasteners into place. They provide from medium power up to the highest power of loads available.
Each strip has 10 powder loads, and there are 10 strips per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator’s manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick View
Anchor Setting Tool Powder Load, 25 Caliber Disc
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .25 caliber powder loads provide the force needed to drive those fasteners into place. This level is the medium strength available, for average fasteners and materials.
Each disc has 10 powder loads, and there are 10 discs per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick View
Lead Wood Screw Anchor
Lead wood screw anchors, also known as lead wood screw shields, are ideally suited for projects that require fastening wood or anchoring brick, concrete, block or softer masonry. You’ll find these anchors install easily as the lead alloy material is soft enough to use, yet hard enough to provide strong holding power. A pre-drilled hole is required for installation.
We do not recommend for ceiling applications. -
Read MoreQuick View
Toggle Bolt, Zinc Plated
The Toggle Bolt is a spring wing type hollow wall anchor designed for use in block, wallboard and other hollow base materials. The Toggle Bolt is a two-part assembly consisting of a machine screw and a spring wing toggle. Sizes range from 1/8″ x 2″ to 1/2″ x 6″ with combo round, flat, mushroom, tie-wire or slotted hex head styles.
-
Read MoreQuick View
Threaded Stud
Threaded studs are available in a variety of thread and shank lengths for use in concrete, some types of concrete block, and A36 or A572 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required or for suspending sprinkler systems.
The threaded studs have a specially designed point to allow proper penetration into the base material. A plastic flute is mounted over the point to retain the drive pin in the fasteners guide of the tool providing guidance during the driving operation. A plastic cap is also provided to protect the threads of the fastener during the driving process as well as providing guidance during installation. -
Read MoreQuick View
E-Z Anchor Drywall Anchors
The E-Z Ancor is a one-piece self-drilling anchor designed for optimal holding performance in drywall. Because it pre-drills its own small precise hole, no hole preparation is necessary.
With a range of choices, including mini, regular and heavy duty, and available in zinc or nylon, there is an E-Z solution to your hanging problems. -
Read MoreQuick View
DeWalt Wood Knockers II
DeWalt Wood-Knocker concrete inserts are installed onto wooden forms used to support newly poured concrete floor slabs, roof slabs or walls. When the forms are stripped, the color-coded flange is visibly embedded in the concrete surface. The inserts allow the attachment of steel threaded rod or threaded bolts in sizes ranging from 1/4″ to 3/4″ in diameter. The hex impact plate offers resistance to rotation within the concrete as a steel threaded rod or threaded bolt is being installed.
-
Read MoreQuick View
Plastic Anchor Kit
This kit contains standard drywall/concrete expansion anchors, screws, and a masonry drill bit sized appropriately.
Kits are available with standard Phillips pan head screws, or with slotted hex head washer screws.
Sizes are:
3/16″ Anchor & Bit, with #6 – #8 x 3/4″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Slot Hex Head Screw -
Read MoreQuick View
Toggle Wing, Zinc Plated
A Toggle spring wing anchor, also called a toggle nut, in zinc plated steel is an anchor used in hollow wall applications (walls with space on the other side) such as drywall and concrete blocks (also called cinder blocks) or any hollow concrete masonry unit. Toggle wings are often used to replace spring wings used in the installations of toggle bolts. Toggle nuts are used with machine screws through pre-drilled holes.
