Ramset T3 Fuel Cell, 2-Pack
All fuel cells replace conventional powder loads and drive more than 1000 shots.
- Description
- Safety & Disposal
- Data Sheets & Downloads
All fuel cells replace conventional powder loads and drive more than 1000 shots.
Disposal
The fuel cell is basically an aerosol can, check with your local regulations for disposal.nbsp;
Fuel Cell: propylene/butylenes mix
Fuel Safety Instructions
Always store fuel cells where they will not be exposed to an open flame, sparks or temperatures above 120 degrees F (48 degrees C).
Fuel cells are good for 12 months. Check expiration date on bottom of can.
Related Products
-
Read MoreQuick ViewT-Nuts
T-nuts are barrel shaped fasteners with internal threading, and are used to provide an anchor point for a bolt in a piece of wood, whether a flat board or a dimensional piece. They are especially useful when a flush surface is wanted. T-nuts have a flat base with prongs bent up at 90° angles, parallel to the barrel. After pre-drilling a hole, the t-nut can be fixed in place either by tightening a bolt into it from the top, which pulls the prongs into the wood, or using hammer to pound the locking prongs into the wood until flush.
-
HotQuick View
Hex Head Cap Screws – Grade 2
Hex Head Cap Screws are designed for easy assembly into a tapped hole. Hex Cap Screws meet SAE specifications with a specially designed washer face under the head and a chamfered point. Plain finish, or bare metal, will have a coating of light oil to resist corrosion. Grade 2 is generally an economical but lower strength fastener. -
Read MoreQuick View
Anchor Setting Tool Powder Load, 25 Caliber Disc
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .25 caliber powder loads provide the force needed to drive those fasteners into place. This level is the medium strength available, for average fasteners and materials.
Each disc has 10 powder loads, and there are 10 discs per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
HotQuick View
Original Wej-It® Wedge Anchors
The Wej-It original Wedge Anchors are time tested with proven reliabilty and has been an industry standard for over 60 years.
-
Quick View
1″ Conduit Clip w/Pin
Designed for use with Powder Actuated tools, this EMT clip will secure conduit to concrete, without the need to drill a hole first.
-
Quick View
Ramset TrakFast Tool
STILL THE MOST REVOLUTIONARY FASTENING SYSTEM IN THE CONSTRUCTION INDUSTRY!
Since its introduction in 1991, TrakFast has been the tool of choice for both interior and exterior contractors. The TrakFast Automatic Fastening System fastens all types of track, from standard track to hat channel, deep leg, Z, and J channel.
-
Quick View
POWER-DROP Drop-In Anchors
POWER-Drop anchors are internally threaded anchors that provide wedge anchor performance with the convenience of a drop-in anchor. The safety shoulder supports the clip when the anchor is under strain to eliminate bolt-end collapse and/or clip slippage under ultimate loading conditions. The POWER-Drop is seismic rated: allowable values may be increased 33.3% for short-term loading in resisting earthquake or wind loads. Numerous head style and size options are available: they may be used with machine screws, tamper-proof bolts, threaded rod and a variety of other male-threaded fastenersCan be used with almost any material, including:
- Normal Weight Concrete
- Lightweight Concrete
- Solid Masonry
-
HotQuick View
Ankr-TITE Wej-It Anchors
This anchor is a high-strength, fully threaded, and torque-controlled expansion anchor designed for anchoring into normal-weight concrete, lightweight concrete, and grouted concrete masonry.
-
HotQuick View
Hex Head Cap Screws – Grade 8
Hex Head Cap Screws are designed for easy assembly into a tapped hole. Hex Cap Screws meet SAE specifications with a specially designed washer face under the head and a chamfered point. Grade 8 has a greater tensile strength than Grade 5. Designed for use in high-strength and high-stress applications. -
Quick View
Elite Beam Clamp
Elite Beam Clamps are used as structural attachments to the top or bottom of metal beams, purlins, channel, or angle iron.
POWER-Drop anchors are internally threaded anchors that provide wedge anchor performance with the convenience of a drop-in anchor. The safety shoulder supports the clip when the anchor is under strain to eliminate bolt-end collapse and/or clip slippage under ultimate loading conditions. The POWER-Drop is seismic rated: allowable values may be increased 33.3% for short-term loading in resisting earthquake or wind loads. Numerous head style and size options are available: they may be used with machine screws, tamper-proof bolts, threaded rod and a variety of other male-threaded fasteners
