Ramset PATCK P.A.T. Cleaning Kit
GENERAL PURPOSE FOR ALL TOOLS
Contains
Handle Brush
Round Wire Tube Brush
Package of Scrubs Cleaners
- Description
GENERAL PURPOSE FOR ALL TOOLS
Contains
Handle Brush
Round Wire Tube Brush
Package of Scrubs Cleaners
Related Products
-
Read MoreQuick ViewAnchor Setting Tool Powder Load, .22 Caliber
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .22 caliber powder loads provide the force needed to drive those fasteners into place. This level is the lightest available, for smaller fasteners and thinner materials.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Quick ViewHeavy Duty Cobalt Drill Bits
Our Cobalt High Speed drill bits are made of high speed Cobalt Steel. The Cobalt content adds high abrasion resistance to the already hard working properties if our bits. Heavy web construction and 135 degree Split-Point add to the long life of these bits. Available in sizes 1/32″ – 1/2″.
-
Quick View
Ramset Ceiling Clip, Gas Actuated
The Ramset Ceiling Clip Assembly is used for suspended ceilings and other wire-held systems. The pre-assembled ceiling clip consists of a zinc-plated 14 gage clip and fastener, and is designed for use in Ramset T3SS Single-Shot Gas Tool.
This assembly does not include a wire, only the ceiling clip. -
Quick View
Ship Auger Drill Bits
Durable hardened cutting edge for long life in tough materials, including nail-embedded wood. Fully-forged bit for maximum durability. Wide flutes for maximum chip removal and less binding. Aggressive screw-pitch for faster drilling. 5/16″ – 1-1/2″ in 6″ and 18″ length.
-
Read MoreQuick View
Ramset Trakfast Pins, Gas Actuated
Ramset TrakFast collated pins are designed for high volume, repetitive fastenings, such as drywall track or wood furring to concrete and steel. They are available in a variety of sizes, finishes, and styles.
-
Quick View
1-1/4″ Ceiling Clip Assembly
The Ramset Ceiling Clip is designed to mount into a slanted ceiling, with hanging wire attached through the eye. Able to support light loads such as suspended ceiling grids.
-
Read MoreQuick View
Threaded Stud
Threaded studs are available in a variety of thread and shank lengths for use in concrete, some types of concrete block, and A36 or A572 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required or for suspending sprinkler systems.
The threaded studs have a specially designed point to allow proper penetration into the base material. A plastic flute is mounted over the point to retain the drive pin in the fasteners guide of the tool providing guidance during the driving operation. A plastic cap is also provided to protect the threads of the fastener during the driving process as well as providing guidance during installation. -
Quick View
HSS Black Oxide Drill Bits
The HSS Black Oxide bits are made in the USA with a 118 degree point and are available from 1/32″ to 11/16″.e”]
-
Quick View
Ramset T3 Fuel Cell, 2-Pack
All fuel cells replace conventional powder loads and drive more than 1000 shots.
-
Read MoreQuick View
Ramset Conduit Clamp, Gas Actuated
The Ramset Conduit Clamp is used to attach conduit to concrete. Pin pre-assembled to an 18 gage conduit clamp, and is designed for use in the Ramset T3SS Single-Shot Gas Tool.
