Ramset PATCK P.A.T. Cleaning Kit
GENERAL PURPOSE FOR ALL TOOLS
Contains
Handle Brush
Round Wire Tube Brush
Package of Scrubs Cleaners
- Description
GENERAL PURPOSE FOR ALL TOOLS
Contains
Handle Brush
Round Wire Tube Brush
Package of Scrubs Cleaners
Related Products
-
Quick ViewHSS Black Oxide Drill Bits
The HSS Black Oxide bits are made in the USA with a 118 degree point and are available from 1/32″ to 11/16″.e”]
-
Read MoreQuick View
Ramset Conduit Clamp, Gas Actuated
The Ramset Conduit Clamp is used to attach conduit to concrete. Pin pre-assembled to an 18 gage conduit clamp, and is designed for use in the Ramset T3SS Single-Shot Gas Tool.
-
Quick View
1″ Conduit Clip w/Pin
Designed for use with Powder Actuated tools, this EMT clip will secure conduit to concrete, without the need to drill a hole first.
-
Read MoreQuick View
Ramset Trakfast Pins, Gas Actuated
Ramset TrakFast collated pins are designed for high volume, repetitive fastenings, such as drywall track or wood furring to concrete and steel. They are available in a variety of sizes, finishes, and styles.
-
Read MoreQuick View
Anchor Setting Tool Powder Load, .22 Caliber
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .22 caliber powder loads provide the force needed to drive those fasteners into place. This level is the lightest available, for smaller fasteners and thinner materials.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Quick View
Ramset Tie Strap Holder
The Ramset Tie Strap Holder is used to install temporary lighting and secure low voltage cable to concrete. It can hold a standard cable tie up to 3/8″ in width. Fastener is pre-assembled to a 22 gage tie strap holder, and is designed for use in Ramset T3SS Single-Shot Gas Tool.
-
Quick View
Spade Drill Bits
Spade bits are used for rough boring in wood. Spade bits are flat, with a centering point and two cutters. The cutters are often equipped with spurs in an attempt to ensure a cleaner hole. Intended for high speed use, they are used with electric hand drills. Spade bits are also sometimes referred to as “paddle bits”. Available in 1/4″ – 1-1/2″.
-
Read MoreQuick View
Anchor Setting Tool Powder Load Strips
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These color coordinated .25 and .27 caliber powder loads provide the force needed to drive those fasteners into place. They provide from medium power up to the highest power of loads available.
Each strip has 10 powder loads, and there are 10 strips per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator’s manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick View
Ramset Washer Pin Fastening Systems
Designed to drive flush into steel and concrete
Consistent and optimum quality in every pin
Washer increases bearing surface against material -
Read MoreQuick View
Ramset One Hole Strap, Gas Actuated
The Ramset One Hole Strap is used to attach EMT conduit or armored cable to concrete. The fastener is pre-assembled to a 16 gage conduit strap, and is designed for use in Ramset T3SS Single-Shot Gas Tool.
