Ramset Ceiling Clip, Gas Actuated
The Ramset Ceiling Clip Assembly is used for suspended ceilings and other wire-held systems. The pre-assembled ceiling clip consists of a zinc-plated 14 gage clip and fastener, and is designed for use in Ramset T3SS Single-Shot Gas Tool.
This assembly does not include a wire, only the ceiling clip.
- Description
- Details
The Ramset Ceiling Clip Assembly is used for suspended ceilings and other wire-held systems. The pre-assembled ceiling clip consists of a zinc-plated 14 gage clip and fastener, and is designed for use in Ramset T3SS Single-Shot Gas Tool.
This assembly does not include a wire, only the ceiling clip.
Related Products
-
Pegatanke Cold-Welding Epoxy, Black
It is a high quality epoxy glue, developed to withstand the most demanding physical and chemical conditions. Used in industrial, automotive, naval, electrical and construction repairs; as well as in the simplest home repairs, thanks to its high resistance to extreme temperatures and voltage.
EXCELLENT FOR:- Petrol tanks
- Water tanks
- Radiators
- Car repairs
-
Read MoreQuick View
DeWalt Wood Knockers II
DeWalt Wood-Knocker concrete inserts are installed onto wooden forms used to support newly poured concrete floor slabs, roof slabs or walls. When the forms are stripped, the color-coded flange is visibly embedded in the concrete surface. The inserts allow the attachment of steel threaded rod or threaded bolts in sizes ranging from 1/4″ to 3/4″ in diameter. The hex impact plate offers resistance to rotation within the concrete as a steel threaded rod or threaded bolt is being installed.
-
Read MoreQuick View
Hollow Wall Anchor, Long and Short
The sleeve type hollow wall anchor is designed for use in base materials such as plaster, wallboard, concrete block, hollow tile or plywood. It is installed using a drill and can be used with various wall thicknesses. The sections of the sleeve expand as the screw is tightened and driven into the wall. The front section of the hollow wall anchor will add permanent screw threads, so that once set, the screw may be removed as often as necessary without affecting the anchor.
These anchors are also known as Molly bolts. -
Read MoreQuick View
Knurled Track Pin
The Ramset 3/4 in. Drive Pins are ideal for fastening track in concrete and can be used to penetrate dense concrete and structural-quality steel. The pins are specifically fabricated for toughness and durability.
-
Read MoreQuick View
Ramset Washer Pin Fastening Systems
Designed to drive flush into steel and concrete
Consistent and optimum quality in every pin
Washer increases bearing surface against material -
Read MoreQuick View
Anchor Setting Tool Powder Load, .22 Caliber
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .22 caliber powder loads provide the force needed to drive those fasteners into place. This level is the lightest available, for smaller fasteners and thinner materials.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick View
Grey Plastic Anchor, No Lip
This is a standard plastic expansion anchor that can be used in drywall or solid walls for light hanging or attaching needs. This type has no outer ring or lip that remains outside the pre-drilled hole, so there will not be any plastic visible once the screw is in place. Also, whatever is being attached to the wall will sit directly against the wall, with no gap.
-
Read MoreQuick View
Ramset Fastening Pins
The Ramset Fastening System Drive Pins are powder actuated pins used to attach material to concrete or steel. The pins are specifically fabricated for toughness and durability.
The 1/2″ and 5/8″ pins are knurled for extra grip, and are specifically engineered for use in structural-quality steel.
The 3/4″ and 1″ pins are perfect for attaching metal track to concrete.
The 1″ up to 2″ pins are sized for attaching furring strips or plywood to concrete.
The 2-1/2″ and 3″ pins are designed to attach 2×4’s to concrete. -
Read MoreQuick View
Anchor Setting Tool Powder Load, 25 Caliber Disc
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .25 caliber powder loads provide the force needed to drive those fasteners into place. This level is the medium strength available, for average fasteners and materials.
Each disc has 10 powder loads, and there are 10 discs per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick View
Plastic Anchor Kit
This kit contains standard drywall/concrete expansion anchors, screws, and a masonry drill bit sized appropriately.
Kits are available with standard Phillips pan head screws, or with slotted hex head washer screws.
Sizes are:
3/16″ Anchor & Bit, with #6 – #8 x 3/4″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Slot Hex Head Screw