- Additional information
- Description
Additional information
Additional information
| Size | 3/16″ x 3/4″, 3/16″ x 1″, 3/16″ x 1-1/4″, 1/4″ x 1″, 1/4″ x 1-1/4″, 1/4″ x 1-1/2″, 1/4″ x 2″, 5/16″ x 1″, 5/16″ x 1-1/4″, 5/16″ x 1-1/2″, 5/16″ x 2″, 3/8″ x 1-1/4″, 3/8″ x 1-1/2″, 3/8″ x 2″, 1/2″ x 2″ |
|---|---|
| Material & Finish | Zinc, Stainless Steel, Stainless Steel 316 |
Description
A fender washer, though similar in shape to a standard washer, differs in that the outside diameter is traditionally much larger in proportion to the center hole. With this design, a fender washer can be placed under the head of a bolt or nut to help distribute forces applied when tightening. Its oversized outside diameter also provides more bearing surface for the load of the fastener—distributing the load further on soft or thin materials. Fender washers are commonly used in automotive, sheet metal, plumbing and electrical applications.
Related Products
-
Quick ViewPAM #8 X 2-1/2″ Roof Tile Screws
Stainless steel tile roofing screws for use with the PAM auto-feed screw system. These screws are #8 x 2-1/2″ and used for attaching roof tile to wood. The type 17 point improves penetration of tile.
Meets Miami-Dade County, FL Protocol PA 114-95, Appendix E, Section 2 (ASTM G85). Box of 1,000 screws. -
Read MoreQuick View
Anchor Bolts, L-Bolts
-
Quick View
PanelMate Quick Kit
This kit contains all of the hardware you need to get started making your home hurricane-resistant. There are 40 PanelMate anchors, along with the bit and driver to properly set them. There are also 40 washers and wing nuts to secure the storm panels to the anchors.
-
Read MoreQuick View
Machine Screws
Machine screws are meant to hold two metal work pieces together, with the use of a threaded pre-tapped hole, or through a hole and held with a nut. They are threaded the entire length of the shank. For most styles of a machine screw, the length is measured from under the head to the end of the screw. For flat head machine screws, since they are intended to fit into a countersunk hole, their length is measured from the top of the screw head to the end of the screw.
-
Read MoreQuick View
F-Track Bolts
The square head of these F-Track Bolts fits perfectly into all flat and angled storm panel F-Track.
-
Read MoreQuick ViewLock Washers
-
Read MoreQuick View
All Thread, Threaded Rod
Threaded rod has continuous threading, either on both ends or it may extend along the complete length of the rod. It has no head or fashioned tip. Threaded rod can be used as an anchor bolt, clamp, hanger or U-bolt.
Threaded rod is available in carbon steel, as Plain, Zinc Plated and HDG, as well as Stainless Steel and the B7/A193 alloy. -
Read MoreQuick View
F436 Structural Washers (SAE)
-
Read MoreQuick View
Square Plate Washer
Square plate washers are made from low carbon steel and have a larger surface area than round washers. Since they develop more friction when tightened against wood, they are often found in timber construction.
Often, square plate washers are used to attach treated lumber sill plates to concrete foundations. Another common use is using square plate washers to attach wood beams to the walls of a garage, and them mount the garage door rails and equipment. -
Read MoreQuick View
Wing Nuts
Wing nuts are a type of specialty nut with a pair of wings to enable it to tighten without tools. The wings provide a grip for the thumb and finger for turning. They are commonly used where frequent adjustments or removals are needed, and can be made quickly at a later stage.
An alternative form of the wing nut has a washer built in, and is used to storm-proof the windows of a building. This washer face allows the wing nut to be used to secure plywood onto fixed anchors, where the hole in the plywood will be larger than the anchor studs it and the wing nut are being mounted on. This provides the advantage of having a larger surface bearing the pressure, while also eliminating the need of a separate washer that will often fall and get lost during storm-prep installation. -
Quick View
PAM #8 X 2-1/2″ Roof Tile Screws
Stainless steel tile roofing screws for use with the PAM auto-feed screw system. These screws are #8 x 2-1/2″ and used for attaching roof tile to wood. The type 17 point improves penetration of tile.
Meets Miami-Dade County, FL Protocol PA 114-95, Appendix E, Section 2 (ASTM G85). Box of 1,000 screws. -
Read MoreQuick View
Anchor Bolts, L-Bolts
-
Quick View
PanelMate Quick Kit
This kit contains all of the hardware you need to get started making your home hurricane-resistant. There are 40 PanelMate anchors, along with the bit and driver to properly set them. There are also 40 washers and wing nuts to secure the storm panels to the anchors.
-
Read MoreQuick View
Machine Screws
Machine screws are meant to hold two metal work pieces together, with the use of a threaded pre-tapped hole, or through a hole and held with a nut. They are threaded the entire length of the shank. For most styles of a machine screw, the length is measured from under the head to the end of the screw. For flat head machine screws, since they are intended to fit into a countersunk hole, their length is measured from the top of the screw head to the end of the screw.
-
Read MoreQuick View
F-Track Bolts
The square head of these F-Track Bolts fits perfectly into all flat and angled storm panel F-Track.
-
Read MoreQuick View
Lock Washers
-
Read MoreQuick View
All Thread, Threaded Rod
Threaded rod has continuous threading, either on both ends or it may extend along the complete length of the rod. It has no head or fashioned tip. Threaded rod can be used as an anchor bolt, clamp, hanger or U-bolt.
Threaded rod is available in carbon steel, as Plain, Zinc Plated and HDG, as well as Stainless Steel and the B7/A193 alloy. -
Read MoreQuick View
F436 Structural Washers (SAE)
-
Read MoreQuick View
Square Plate Washer
Square plate washers are made from low carbon steel and have a larger surface area than round washers. Since they develop more friction when tightened against wood, they are often found in timber construction.
Often, square plate washers are used to attach treated lumber sill plates to concrete foundations. Another common use is using square plate washers to attach wood beams to the walls of a garage, and them mount the garage door rails and equipment. -
Read MoreQuick View
Wing Nuts
Wing nuts are a type of specialty nut with a pair of wings to enable it to tighten without tools. The wings provide a grip for the thumb and finger for turning. They are commonly used where frequent adjustments or removals are needed, and can be made quickly at a later stage.
An alternative form of the wing nut has a washer built in, and is used to storm-proof the windows of a building. This washer face allows the wing nut to be used to secure plywood onto fixed anchors, where the hole in the plywood will be larger than the anchor studs it and the wing nut are being mounted on. This provides the advantage of having a larger surface bearing the pressure, while also eliminating the need of a separate washer that will often fall and get lost during storm-prep installation.
