DekTite Pipe Flashing System
DekTite pipe flashings are made of long life, flexible, weatherproof gray EPDM rubber that will not crack or break. A flexible, corrosion resistant aluminum base conforms to any panel configuration. Pipe diameter markings are clearly indicated for accurate fitting on pipes from 1/4″ to 18″ diameter.
The Retrofit version has a mechanical joiner seam, and fits around existing continuous pipe, rather than sliding over. It can also simply be used for taller pipes if needed.
One piece construction is easy to install and pleated the cone adjusts to any roof pitch, allowing for complete flexibility.
- Additional information
- Description
- Data Sheets & Downloads
Additional information
| Style/Size | #3, New Install, 1/4″ – 5″ OD, #5, New Install, 4″ – 7″ OD, #802, Retrofit, 2″ – 7-1/4″ OD |
|---|
DekTite pipe flashings are made of long life, flexible, weatherproof gray EPDM rubber that will not crack or break. A flexible, corrosion resistant aluminum base conforms to any panel configuration. Pipe diameter markings are clearly indicated for accurate fitting on pipes from 1/4" to 18" diameter.
The Retrofit version has a mechanical joiner seam, and fits around existing continuous pipe, rather than sliding over. It can also simply be used for taller pipes if needed.
One piece construction is easy to install and pleated the cone adjusts to any roof pitch, allowing for complete flexibility.
EPDM has a continuous service temperature range of -65ºF to +250ºF.
Also available in Red Silicone, which has a continuous service temperature range of -40ºF to +350ºF.
All DekTite products have proven resistance to ozone and ultra-violet light.
Related Products
-
Quick View2-Hole Corner Angle L Bracket B
This connector is used for connecting metal struts together, as a 90° angle. The two sides are 2″ and 1-7/8″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance. -
Quick ViewElite Loop Hanger
Elite Loop Hangers are the recommended pipe support solution for the suspension of stationary non-insulated pipe lines.
-
Quick View
Purlin Clamp, 3/8″
Purlin clamps provide structural attachment specifically to the purlins that support a roof. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room.
-
Quick View
2-Hole Closed 45 Degree Angle Connector
This connector is used for connecting metal struts together, at a 45° angle. The two sides are 3-1/2″ and 2-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Read MoreQuick View
Junior Beam Clamp, Galvanized, Shiny
Beam clamps provide structural attachment to the flange of metal beams, purlins, channel strut, or angle iron. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room. With its galvanized coating, this clamp can also be used in exterior or open building situations. -
Quick View
Elite Copper Loop Hanger
Elite Copper Loop Hangers are required for hanging copper pipe and allows for vertical adjustment of pipe after installation.
-
Read MoreQuick View
Gasket, Full Face, Black Neoprene
Neoprene gaskets are used to seal the connection space between two pipes, or other objects. The neoprene material is an excellent choice, because it exhibits good chemical stability and maintains flexibility over a wide temperature range.
-
Quick View
2-Hole Corner Angle L Bracket A
This connector is used for connecting metal struts together, as a 90° angle. The two sides are 2-1/4″ and 1-5/8″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Read MoreQuick View
Concrete Forms, Econ-O-Sleeve
Econ-O-Sleeve Hole Forms consistently form round, smooth, uniform holes and are available in a broad range of diameters. They may be cut, stacked, or telescoped for any slab thickness.
Form holes, don’t drill em!
Econ-O-Sleeve forms come in a variety of diameters, and adjust for any slab thickness by stacking two or more together. -
Quick View
Standard Riser Clamps (6200-6300)
Model 6200-6300 Standard Riser Clamps from Elite components are designed for standard iron pipe. They are available in either galvanized or plain and in sizes from 1/2″ thru 24″.
Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8)
