Ramset PATCK P.A.T. Cleaning Kit
GENERAL PURPOSE FOR ALL TOOLS
Contains
Handle Brush
Round Wire Tube Brush
Package of Scrubs Cleaners
- Description
GENERAL PURPOSE FOR ALL TOOLS
Contains
Handle Brush
Round Wire Tube Brush
Package of Scrubs Cleaners
Related Products
-
Quick ViewRamset Tie Strap Holder
The Ramset Tie Strap Holder is used to install temporary lighting and secure low voltage cable to concrete. It can hold a standard cable tie up to 3/8″ in width. Fastener is pre-assembled to a 22 gage tie strap holder, and is designed for use in Ramset T3SS Single-Shot Gas Tool.
-
Quick View
Powers Fuel Cell C3
Powers Fasteners Trak-It Fuel cells are color coded. Blue fuel cells work with C3 Trak-It tools. Each cell is expected to last through approximately 1000 pins.
Fuel cells work in temperatures down to 10° F. -
Read MoreQuick View
Ramset Conduit Clamp, Gas Actuated
The Ramset Conduit Clamp is used to attach conduit to concrete. Pin pre-assembled to an 18 gage conduit clamp, and is designed for use in the Ramset T3SS Single-Shot Gas Tool.
-
Quick View
“Silver & Deming” Drill Bits
One particular type of reduced-shank drill bits are Silver & Deming (S&D) bits, whose sets run from 33/64″ to 1″ drill body diameter with a standard 1/2″ reduced shank for all. This allows drill presses with 1/2″ chucks to run the larger drills. S&D bits are 6″ in length with a 3″ drilling depth.
-
Read MoreQuick View
Ramset Fastening Pins
The Ramset Fastening System Drive Pins are powder actuated pins used to attach material to concrete or steel. The pins are specifically fabricated for toughness and durability.
The 1/2″ and 5/8″ pins are knurled for extra grip, and are specifically engineered for use in structural-quality steel.
The 3/4″ and 1″ pins are perfect for attaching metal track to concrete.
The 1″ up to 2″ pins are sized for attaching furring strips or plywood to concrete.
The 2-1/2″ and 3″ pins are designed to attach 2×4’s to concrete. -
Quick View
Ramset Plated Pin w/Top Hat
The Ramset Plated Pin with Top Hat is used for general purpose fastening to concrete. The fasteners are designed for use inRamset T3SS Single-Shot Gas Tool.
-
Quick View
Ramset TrakFast Tool
STILL THE MOST REVOLUTIONARY FASTENING SYSTEM IN THE CONSTRUCTION INDUSTRY!
Since its introduction in 1991, TrakFast has been the tool of choice for both interior and exterior contractors. The TrakFast Automatic Fastening System fastens all types of track, from standard track to hat channel, deep leg, Z, and J channel.
-
Quick View
Spade Drill Bits
Spade bits are used for rough boring in wood. Spade bits are flat, with a centering point and two cutters. The cutters are often equipped with spurs in an attempt to ensure a cleaner hole. Intended for high speed use, they are used with electric hand drills. Spade bits are also sometimes referred to as “paddle bits”. Available in 1/4″ – 1-1/2″.
-
Quick View
Ship Auger Drill Bits
Durable hardened cutting edge for long life in tough materials, including nail-embedded wood. Fully-forged bit for maximum durability. Wide flutes for maximum chip removal and less binding. Aggressive screw-pitch for faster drilling. 5/16″ – 1-1/2″ in 6″ and 18″ length.
-
Read MoreQuick View
Ramset Washer Pin Fastening Systems
Designed to drive flush into steel and concrete
Consistent and optimum quality in every pin
Washer increases bearing surface against material
