Ramset Tie Strap Holder
The Ramset Tie Strap Holder is used to install temporary lighting and secure low voltage cable to concrete. It can hold a standard cable tie up to 3/8″ in width. Fastener is pre-assembled to a 22 gage tie strap holder, and is designed for use in Ramset T3SS Single-Shot Gas Tool.
- Description
- Details
The Ramset Tie Strap Holder is used to install temporary lighting and secure low voltage cable to concrete. It can hold a standard cable tie up to 3/8" in width. Fastener is pre-assembled to a 22 gage tie strap holder, and is designed for use in Ramset T3SS Single-Shot Gas Tool.
Related Products
-
Read MoreQuick ViewLead Wood Screw Anchor
Lead wood screw anchors, also known as lead wood screw shields, are ideally suited for projects that require fastening wood or anchoring brick, concrete, block or softer masonry. You’ll find these anchors install easily as the lead alloy material is soft enough to use, yet hard enough to provide strong holding power. A pre-drilled hole is required for installation.
We do not recommend for ceiling applications. -
Quick View1-1/4″ Ceiling Clip Assembly
The Ramset Ceiling Clip is designed to mount into a slanted ceiling, with hanging wire attached through the eye. Able to support light loads such as suspended ceiling grids.
-
Read MoreQuick View
Hollow Wall Anchor, Long and Short
The sleeve type hollow wall anchor is designed for use in base materials such as plaster, wallboard, concrete block, hollow tile or plywood. It is installed using a drill and can be used with various wall thicknesses. The sections of the sleeve expand as the screw is tightened and driven into the wall. The front section of the hollow wall anchor will add permanent screw threads, so that once set, the screw may be removed as often as necessary without affecting the anchor.
These anchors are also known as Molly bolts. -
Read MoreQuick View
Threaded Stud
Threaded studs are available in a variety of thread and shank lengths for use in concrete, some types of concrete block, and A36 or A572 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required or for suspending sprinkler systems.
The threaded studs have a specially designed point to allow proper penetration into the base material. A plastic flute is mounted over the point to retain the drive pin in the fasteners guide of the tool providing guidance during the driving operation. A plastic cap is also provided to protect the threads of the fastener during the driving process as well as providing guidance during installation. -
Read MoreQuick View
Lag Shield, Long and Short
The Lag Shield is a screw style anchor designed for use with lag bolts. It is suitable for use in concrete and the mortar joints of block or brick walls. In harder masonry materials, short style Lag Shields are used to reduce drilling time. The long style version is used in soft or weak masonry to better develop strength. The Lag Shield is not recommended for overhead or life safety applications.
-
Read MoreQuick View
Toggle Wing, Zinc Plated
A Toggle spring wing anchor, also called a toggle nut, in zinc plated steel is an anchor used in hollow wall applications (walls with space on the other side) such as drywall and concrete blocks (also called cinder blocks) or any hollow concrete masonry unit. Toggle wings are often used to replace spring wings used in the installations of toggle bolts. Toggle nuts are used with machine screws through pre-drilled holes.
-
Read MoreQuick View
Hammer Drive Pins
Drive pin anchors are installed in pre-drilled holes with a hammer strike that drives a nail into the anchor body, expanding the anchor to form a tight fit. These anchors secure light loads to masonry materials.
-
Read MoreQuick View
DeWalt Wood Knockers II
DeWalt Wood-Knocker concrete inserts are installed onto wooden forms used to support newly poured concrete floor slabs, roof slabs or walls. When the forms are stripped, the color-coded flange is visibly embedded in the concrete surface. The inserts allow the attachment of steel threaded rod or threaded bolts in sizes ranging from 1/4″ to 3/4″ in diameter. The hex impact plate offers resistance to rotation within the concrete as a steel threaded rod or threaded bolt is being installed.
-
Read MoreQuick View
Plastic Anchor Kit
This kit contains standard drywall/concrete expansion anchors, screws, and a masonry drill bit sized appropriately.
Kits are available with standard Phillips pan head screws, or with slotted hex head washer screws.
Sizes are:
3/16″ Anchor & Bit, with #6 – #8 x 3/4″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Slot Hex Head Screw -
Read MoreQuick View
Lead Hammer Drive Anchor
The Hammer-Set anchor is a mechanical drive anchor consisting of a zinc die cast expansion body and zinc plated steel expander drive pin. Hammer-Set anchors are medium-duty anchors designed for a variety of fastening applications in concrete, block, and brick. It is ideal for light-duty and tamper-resistant applications. Use Hammer-Set anchors to attach termination bars, drywall track, electrical boxes and clips, flashing, lumber and more.
