U-Bolt Style Beam to Channel Clamp
The U-Bolt style beam-to-channel clamp features a piece of bent plate and a u-bolt that is threaded on both sides to secure a strut in place against a beam. The strut is fed through the u-bolt, which is then tightened to secure both the plate to the beam and the strut to the plate. U-style beam clamps can be used to secure strut to either the underside of the beam or the inside of the beam, depending on the configuration of the clamp.
- Description
The U-Bolt style beam-to-channel clamp features a piece of bent plate and a u-bolt that is threaded on both sides to secure a strut in place against a beam. The strut is fed through the u-bolt, which is then tightened to secure both the plate to the beam and the strut to the plate. U-style beam clamps can be used to secure strut to either the underside of the beam or the inside of the beam, depending on the configuration of the clamp.
Related Products
-
Quick ViewStandard Riser Clamps (6200-6300)
Model 6200-6300 Standard Riser Clamps from Elite components are designed for standard iron pipe. They are available in either galvanized or plain and in sizes from 1/2″ thru 24″.
Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8)
-
Read MoreQuick View
Caddy 1-Hole Strap for Conduit
The CPVC One Hole Wrap Around Pipe Strap is designed to support pipe running horizontally on side of a beam, or as a guide to mount CPVC pipe running perpendicular across the top of a beam, or on a vertical run. Model 1070 may be installed onto wood using supplied fastener, or into minimum 20 gauge steel using one 1/4″ x 1 tek screw.
-
Read MoreQuick View
Gasket, Full Face, Red Rubber
These gaskets are comprised of red rubber, a copolymer of Styrene and Butadiene, also known as SBR. It feature excellent impact and tensile strength, good resistance to abrasion and easily conforms to uneven flange surfaces.
This Synthetic material was developed as an alternative to Natural Rubber. The red rubber gaskets are recommended for service in cold and hot water, air, steam,and some weak acids. It should not be used with strong acids, oils, grease, and chlorates -
Read MoreQuick View
Caddy Two-Hole Strap for CPVC Pipe
Caddy 2-Hole Strap helps with the installation of CPVC pipe on wood, masonry or other surface when extra load bearing is needed. Its curved shape positively snaps onto the pipe, making installation easier. For indoor or outdoor applications.
-
Read MoreQuick View
Caddy Stand-Off Strap, 2-Hole for Conduit
Two-hole stand-off straps are used for mounting CPVC pipe to a wall, ceiling, or other surface. They eliminate the need for wood blocks under the pipe. They position the pipe 1-1/2″ off the surface.
-
Read MoreQuick View
Junior Beam Clamp, Galvanized, Shiny
Beam clamps provide structural attachment to the flange of metal beams, purlins, channel strut, or angle iron. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room. With its galvanized coating, this clamp can also be used in exterior or open building situations. -
Quick View
Elite Beam Clamp
Elite Beam Clamps are used as structural attachments to the top or bottom of metal beams, purlins, channel, or angle iron.
-
Quick View
2-Hole Closed 45 Degree Angle Connector
This connector is used for connecting metal struts together, at a 45° angle. The two sides are 3-1/2″ and 2-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Quick View
Elite Loop Hanger
Elite Loop Hangers are the recommended pipe support solution for the suspension of stationary non-insulated pipe lines.
-
Quick View
8-Hole Strut Wing Corner Connector
This connector is used for connecting metal struts together, with the ends of two against a third strut between them. An electro-galvanized coating provides rust resistance.
