Name: Sleeve-TITE Sleeve Expansion Anchors
SKU: Sleeve-TITE
Availability: InStock

Hot

Sleeve-TITE Sleeve Expansion Anchors

Sleeve-TITE Expansion Anchors come fully assembled and ready to use. This speeds installation and eliminates the problem of missing components. Sleeve-TITE is suitable for a wide variety of applications and available with acorn or hex nut, or flat head, or with rod coupling.

Can be used with almost any material, including:

Normal Weight Concrete
Lightweight Concrete
Hollow Masonry
Solid Masonry

Size

Clear

Add to Project List

Add to quote

SKU: Sleeve-TITE Category: Sleeve Anchors Tags: Anchors, Sleeve Anchors, Wej-It

Description

Fully assembled and ready to use
- Speeds installation
- Eliminates the problem of missing components
Suitable for a wide variety of applications
Available with acorn or hex nut, or flat head, or with rod coupling

Additional information

Size	Acorn, 1/4” x 1-3/8”, Acorn, 1/4” x 2-1/4”, Hex, 5/16” x 1-1/2”, Hex, 5/16” x 2-1/2”, Hex, 3/8” x 1-7/8”, Hex, 3/8” x 3”, Hex, 3/8” x 4”, Hex, 1/2” x 2-1/4”, Hex, 1/2” x 3”, Hex, 1/2” x 4”, Hex, 1/2” x 6”, Hex, 5/8” x 2-1/4”, Hex, 5/8 x 3”, Hex, 5/8” x 4-1/4”, Hex, 5/8” x 6”, Hex, 3/4” x 2-1/2”, Hex, 3/4” x 4”, Hex, 3/4” x 6-1/4”, Coupling, 3/8” x 1-7/8”, Coupling, 1/2” x 2-1/4”, Flat, 1/4” x 2”, Flat, 1/4” x 3”, Flat, 3/8” x 4”, Flat, 3/8” x 5”, Flat, 3/8” x 6”, Flat, 1/4” x 3”, Stainles Steel, Flat, 3/8” x 3”, 304, Stainles Steel, Flat, 3/8” x 4”, 304, Stainles Steel, Hex, 3/8” x 1-7/8”, 303, Stainles Steel, Hex, 3/8” x 3”, 303, Stainles Steel, Hex, 1/2” x 3”, 303, Stainles Steel, Hex, 1/2” x 4”, 303, Stainles Steel

Installation Instructions

Drill the hole, whose diameter equals the anchor diameter, perpendicular to the work surface. To assure full holding power, do not ream the hole or allow the drill to wobble.
Drill the hole deeper than the intended embedment, but not closer than two diameters to the opposite surface of the concrete.
A clean hole is necessary for proper performance. Clean the hole using a nylon brush and compressed air.
Assemble the nut and washer so that the top of the nut is flush with the top of the anchor. Drive the anchor through the material to be fastened so that the nut and washer are flush with the surface of the material.
Tighten the nut, or head, 3 to 5 turns past the hand tight position. Installing the "Ankr-TITE^® Series" of anchors with a torque wrench is recommended for optimum performance. Refer to adjacent chart.*

NOTE: Always wear safety glasses. Follow drill manufacturer's instructions. Use only solid carbide-tipped drill bits meeting ANSI B212.15 diameter standards.

Can be used with almost any material, including: