Red Head Epoxy Nozzle, Standard and Specialty
There are currently five nozzles available for the Red Head epoxy tubes. And because all of the epoxy packages have the same threaded outflow connector, each nozzle works with each size of each epoxy product line.
A24S- Mixing Nozzle, fits holes for 3/8” to 5/8″ anchor
S55 – Standard Mixing Nozzle, fits holes for 3/8” anchor or larger
E55 – Long Mixing Nozzle, fits holes for 3/8” anchor or larger
S75 – High Flow Mixing Nozzle, fits holes for 3/4” anchor or larger
S75EXT – Extension for S75 High Flow Mixing Nozzle
- Additional information
- Description
Additional information
| Option | A24S Basic, S55 Standard, E55 Long, S75 High Flow, S75EXT Extension |
|---|
There are currently five nozzles available for the Red Head epoxy tubes. And because all of the epoxy packages have the same threaded outflow connector, each nozzle works with each size of each epoxy line.
A24S Basic Mixing Nozzle
Included with A7+ 10 oz package.
Fits 3/8” to 5/8” holes (overall length of nozzle 6-3/8”).
S55 Standard Mixing Nozzle
Fits holes for 3/8” diameter anchors and larger.
3-1/2” inch usable length for 3/8” and 1/2” anchors.
8-1/4” usable length for 5/8” anchors and above.
E55 Long Mixing Nozzle
Fits holes for 3/8” diameter anchors and larger.
5-3/4” inch usable length for 3/8” and 1/2” anchors.
12-5/8” usable length for 5/8” anchors and above.
S75 High Flow Mixing Nozzle
Fits holes for ¾” diameter anchors and larger.
7-3/8” usable length .
S75EXT Extension for High Flow Mixing Nozzle
For 3/4” diameter anchors and larger.
15-5/8” usable length when attached to S75.
Related Products
-
Quick ViewHammer Drive Tool
Drive pin anchors are installed in pre-drilled holes. Using this tool and a hammer, a solid strike drives a nail into the anchor body, expanding the anchor to form a tight fit. These anchors secure light loads to masonry materials.
-
Read MoreQuick ViewLead Hammer Drive Anchor
The Hammer-Set anchor is a mechanical drive anchor consisting of a zinc die cast expansion body and zinc plated steel expander drive pin. Hammer-Set anchors are medium-duty anchors designed for a variety of fastening applications in concrete, block, and brick. It is ideal for light-duty and tamper-resistant applications. Use Hammer-Set anchors to attach termination bars, drywall track, electrical boxes and clips, flashing, lumber and more.
-
Read MoreQuick View
Knurled Track Pin
The Ramset 3/4 in. Drive Pins are ideal for fastening track in concrete and can be used to penetrate dense concrete and structural-quality steel. The pins are specifically fabricated for toughness and durability.
-
HotQuick View
Original Wej-It® Wedge Anchors
The Wej-It original Wedge Anchors are time tested with proven reliabilty and has been an industry standard for over 60 years.
-
Read MoreQuick View
Grey Plastic Anchor, No Lip
This is a standard plastic expansion anchor that can be used in drywall or solid walls for light hanging or attaching needs. This type has no outer ring or lip that remains outside the pre-drilled hole, so there will not be any plastic visible once the screw is in place. Also, whatever is being attached to the wall will sit directly against the wall, with no gap.
-
Read MoreQuick View
Lead Wood Screw Anchor
Lead wood screw anchors, also known as lead wood screw shields, are ideally suited for projects that require fastening wood or anchoring brick, concrete, block or softer masonry. You’ll find these anchors install easily as the lead alloy material is soft enough to use, yet hard enough to provide strong holding power. A pre-drilled hole is required for installation.
We do not recommend for ceiling applications. -
Read MoreQuick View
Anchor Setting Tool Powder Load Strips
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These color coordinated .25 and .27 caliber powder loads provide the force needed to drive those fasteners into place. They provide from medium power up to the highest power of loads available.
Each strip has 10 powder loads, and there are 10 strips per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator’s manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick View
Ramset Washer Pin Fastening Systems
Designed to drive flush into steel and concrete
Consistent and optimum quality in every pin
Washer increases bearing surface against material -
Read MoreQuick View
Threaded Stud
Threaded studs are available in a variety of thread and shank lengths for use in concrete, some types of concrete block, and A36 or A572 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required or for suspending sprinkler systems.
The threaded studs have a specially designed point to allow proper penetration into the base material. A plastic flute is mounted over the point to retain the drive pin in the fasteners guide of the tool providing guidance during the driving operation. A plastic cap is also provided to protect the threads of the fastener during the driving process as well as providing guidance during installation. -
Read MoreQuick View
Plastic Anchor Kit
This kit contains standard drywall/concrete expansion anchors, screws, and a masonry drill bit sized appropriately.
Kits are available with standard Phillips pan head screws, or with slotted hex head washer screws.
Sizes are:
3/16″ Anchor & Bit, with #6 – #8 x 3/4″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Slot Hex Head Screw
