Ramset Fastening Pins
The Ramset Fastening System Drive Pins are powder actuated pins used to attach material to concrete or steel. The pins are specifically fabricated for toughness and durability.
The 1/2″ and 5/8″ pins are knurled for extra grip, and are specifically engineered for use in structural-quality steel.
The 3/4″ and 1″ pins are perfect for attaching metal track to concrete.
The 1″ up to 2″ pins are sized for attaching furring strips or plywood to concrete.
The 2-1/2″ and 3″ pins are designed to attach 2×4’s to concrete.
- Additional information
- Description
- Cautions
- Data Sheets & Downloads
Additional information
| Size | 1/2″, 5/8″, 3/4″, 1″, 1-1/4″, 1-1/2″, 2″, 2-1/2″, 3″ |
|---|
The Ramset Fastening System Drive Pins are powder actuated pins used to attach material to concrete or steel. The pins are specifically fabricated for toughness and durability.
The 1/2" and 5/8" pins are knurled for extra grip, and are specifically engineered for use in structural-quality steel.
The 3/4" and 1" pins are perfect for attaching metal track to concrete.
The 1" up to 2" pins are sized for attaching furring strips or plywood to concrete.
The 2-1/2" and 3" pins are designed to attach 2x4's to concrete.
Caution: Always wear eye and ear protection at all times. If you aren't sure which power level to use then start with a lower level and work your way up. And remember that 1" of penetration into concrete is the rule of thumb. And yes, with the proper power level and correct length you can fasten to structural steel. But beware the noise and the recoil.
Related Products
-
Read MoreQuick ViewE-Z Anchor Drywall Anchors
The E-Z Ancor is a one-piece self-drilling anchor designed for optimal holding performance in drywall. Because it pre-drills its own small precise hole, no hole preparation is necessary.
With a range of choices, including mini, regular and heavy duty, and available in zinc or nylon, there is an E-Z solution to your hanging problems. -
Quick ViewHammer Drive Tool
Drive pin anchors are installed in pre-drilled holes. Using this tool and a hammer, a solid strike drives a nail into the anchor body, expanding the anchor to form a tight fit. These anchors secure light loads to masonry materials.
-
Read MoreQuick View
Plastic Anchor Kit
This kit contains standard drywall/concrete expansion anchors, screws, and a masonry drill bit sized appropriately.
Kits are available with standard Phillips pan head screws, or with slotted hex head washer screws.
Sizes are:
3/16″ Anchor & Bit, with #6 – #8 x 3/4″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Slot Hex Head Screw -
Quick View
1-1/4″ Ceiling Clip Assembly
The Ramset Ceiling Clip is designed to mount into a slanted ceiling, with hanging wire attached through the eye. Able to support light loads such as suspended ceiling grids.
-
Quick View
1/2″ Combo Bit for 1/4″ Lead M/S Anchor
This 1/2″ combo drill bit installs lead anchors for 1/4″-20 combo sidewalk bolts. I works for all masonry surfaces, both block and concrete. The smaller pilot bit starts the hole in the right location, and the larger 1/2″ step bit drills the perfect hole for setting lead machine screw anchors.
Fully adjustable collar allows you to set the depth of the hole for a perfect set every-time. Comes with Hex Wrench. -
Read MoreQuick View
Toggle Bolt, Zinc Plated
The Toggle Bolt is a spring wing type hollow wall anchor designed for use in block, wallboard and other hollow base materials. The Toggle Bolt is a two-part assembly consisting of a machine screw and a spring wing toggle. Sizes range from 1/8″ x 2″ to 1/2″ x 6″ with combo round, flat, mushroom, tie-wire or slotted hex head styles.
-
HotQuick View
Ankr-TITE® CCAT Cracked Concrete Wedge Anchors
The CCAT Cracked Concrete Wedge Anchors are engineered to provide superior performance in cracked concrete in both seismic and wind load conditions.
-
Read MoreQuick View
Lead Hammer Drive Anchor
The Hammer-Set anchor is a mechanical drive anchor consisting of a zinc die cast expansion body and zinc plated steel expander drive pin. Hammer-Set anchors are medium-duty anchors designed for a variety of fastening applications in concrete, block, and brick. It is ideal for light-duty and tamper-resistant applications. Use Hammer-Set anchors to attach termination bars, drywall track, electrical boxes and clips, flashing, lumber and more.
-
Read MoreQuick View
Hollow Wall Anchor, Long and Short
The sleeve type hollow wall anchor is designed for use in base materials such as plaster, wallboard, concrete block, hollow tile or plywood. It is installed using a drill and can be used with various wall thicknesses. The sections of the sleeve expand as the screw is tightened and driven into the wall. The front section of the hollow wall anchor will add permanent screw threads, so that once set, the screw may be removed as often as necessary without affecting the anchor.
These anchors are also known as Molly bolts. -
Read MoreQuick View
Lead Machine Screw Anchor
The lead machine screw anchor is an internally threaded anchor designed to make female threads into concrete. It features a soft lead shell on the outside and steel threads on the inside. They are designed for solid concrete but can be installed into hollow block or brick with a special setting tool.
