Junior Beam Clamp, Galvanized, Shiny
|
- Additional information
- Description
- Loads and Dimensions Chart
Additional information
| Size | 1/4″, 3/8″, 1/2″, 5/8″, 3/4″, 7/8″ |
|---|
|
Because this beam clamp is electroplated with zinc, it is rust-resistant. It is an acceptable choice when doing work in open-air or exposed spaces.
Also, with its shiny coating, some will prefer it for interior use over the plain finish, to match other visible metalwork in appearance. |
Related Products
-
Quick ViewStandard Riser Clamps (6200-6300)
Model 6200-6300 Standard Riser Clamps from Elite components are designed for standard iron pipe. They are available in either galvanized or plain and in sizes from 1/2″ thru 24″.
Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8)
-
Quick View
4-Hole Closed 45 Degree Angle Connector
This connector is used for connecting metal struts together, at a 45° angle. The two sides are 3-1/2″ and 4-1/8″ long, with four 9/16″ holes to secure it to struts, or other surfaces. An electro-galvanized coating provides rust resistance.
-
Quick View
4-Hole Corner Angle L Bracket
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 4-1/8″ and 3-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Quick View
Elite Loop Hanger
Elite Loop Hangers are the recommended pipe support solution for the suspension of stationary non-insulated pipe lines.
-
Read MoreQuick View
Gasket, Ring, Red Rubber
These gaskets are comprised of red rubber, a copolymer of Styrene and Butadiene, also known as SBR. It feature excellent impact and tensile strength, good resistance to abrasion and easily conforms to uneven flange surfaces.
This Synthetic material was developed as an alternative to Natural Rubber. The red rubber gaskets are recommended for service in cold and hot water, air, steam,and some weak acids. It should not be used with strong acids, oils, grease, and chlorates -
Quick View
2-Hole Corner Angle L Bracket B
This connector is used for connecting metal struts together, as a 90° angle. The two sides are 2″ and 1-7/8″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance. -
Read MoreQuick View
Ceiling Flange, Plain
Ceiling flanges are used to secure threaded rod to a ceiling, so that equipment can be attached to the threaded rod. These flanges are designed to either support 3/8″-16 rod, or 1/2″-13 rod. They have a natural, plain finish, and are excellent choice for interior use.
-
Quick View
4-Hole Corner Angle L Bracket, Stainless
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 4-1/8″ long, with three 9/16″ holes to secure to struts or other surfaces. Stainless steel material makes this product more rust resistant, and it is suitable for exterior uses where rain or salt water are expected.
-
Quick View
3-Hole Corner Angle L Bracket
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 2-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Read MoreQuick View
Concrete Forms, Econ-O-Sleeve
Econ-O-Sleeve Hole Forms consistently form round, smooth, uniform holes and are available in a broad range of diameters. They may be cut, stacked, or telescoped for any slab thickness.
Form holes, don’t drill em!
Econ-O-Sleeve forms come in a variety of diameters, and adjust for any slab thickness by stacking two or more together.
