Pegatanke Cold-Welding Epoxy, Steel, Grey
It is a two-component epoxy glue developed to be used as adhesive or anchor mortar between different materials. Pegatanke Steel offers longer life span for jobs subjected to extreme temperature and stress resistance conditions. Ideal for industry and heavy duty. Fully functional dry and
- Description
- Instructions
- Data Sheets & Downloads
It is a two-component epoxy glue developed to be used as adhesive or anchor mortar between different materials. Pegatanke Steel offers longer life span for jobs subjected to extreme temperature and stress resistance conditions. Ideal for industry and heavy duty. Fully functional dry and underwater.
EXCELLENT FOR:
- Engines
- Anchors
- Hardware
- Machinery
- Mortars
USE INSTRUCTIONS:
- Thoroughly clean the area or surface where the glue will be applied.
- Mix components 1 and 2 in equal parts.
- Stir the components for 3 minutes until obtaining homogeneous consistency.
- Apply the mixture evenly in amounts proportional to the surface to be repaired.
- Join the parts to be glued together and secure them if needed for them to remain steady.
- Let dry for 30 minutes in the sun or 1 ½ hours in the shade (under roof or in cloudy days). This time may vary according to room temperature. See packaging for more information.
USED IN:
Aluminium • Ceramic • Copper • Fibreglass • Slab • Plastic • Wood • Metal • MDF • Glass
Safety Data Sheet
Equivalent SDS from another Manufacturer
Related Products
-
Read MoreQuick ViewAnchor Setting Tool Powder Load, 25 Caliber Disc
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .25 caliber powder loads provide the force needed to drive those fasteners into place. This level is the medium strength available, for average fasteners and materials.
Each disc has 10 powder loads, and there are 10 discs per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick ViewE-Z Anchor Drywall Anchors
The E-Z Ancor is a one-piece self-drilling anchor designed for optimal holding performance in drywall. Because it pre-drills its own small precise hole, no hole preparation is necessary.
With a range of choices, including mini, regular and heavy duty, and available in zinc or nylon, there is an E-Z solution to your hanging problems. -
Read MoreQuick View
DeWalt Wood Knockers II
DeWalt Wood-Knocker concrete inserts are installed onto wooden forms used to support newly poured concrete floor slabs, roof slabs or walls. When the forms are stripped, the color-coded flange is visibly embedded in the concrete surface. The inserts allow the attachment of steel threaded rod or threaded bolts in sizes ranging from 1/4″ to 3/4″ in diameter. The hex impact plate offers resistance to rotation within the concrete as a steel threaded rod or threaded bolt is being installed.
-
Read MoreQuick View
Plastic Anchor Kit
This kit contains standard drywall/concrete expansion anchors, screws, and a masonry drill bit sized appropriately.
Kits are available with standard Phillips pan head screws, or with slotted hex head washer screws.
Sizes are:
3/16″ Anchor & Bit, with #6 – #8 x 3/4″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Slot Hex Head Screw -
Read MoreQuick View
Ramset Fastening Pins
The Ramset Fastening System Drive Pins are powder actuated pins used to attach material to concrete or steel. The pins are specifically fabricated for toughness and durability.
The 1/2″ and 5/8″ pins are knurled for extra grip, and are specifically engineered for use in structural-quality steel.
The 3/4″ and 1″ pins are perfect for attaching metal track to concrete.
The 1″ up to 2″ pins are sized for attaching furring strips or plywood to concrete.
The 2-1/2″ and 3″ pins are designed to attach 2×4’s to concrete. -
Read MoreQuick View
Toggle Bolt, Zinc Plated
The Toggle Bolt is a spring wing type hollow wall anchor designed for use in block, wallboard and other hollow base materials. The Toggle Bolt is a two-part assembly consisting of a machine screw and a spring wing toggle. Sizes range from 1/8″ x 2″ to 1/2″ x 6″ with combo round, flat, mushroom, tie-wire or slotted hex head styles.
-
Read MoreQuick View
Anchor Setting Tool Powder Load, .22 Caliber
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .22 caliber powder loads provide the force needed to drive those fasteners into place. This level is the lightest available, for smaller fasteners and thinner materials.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Quick View
1″ Conduit Clip w/Pin
Designed for use with Powder Actuated tools, this EMT clip will secure conduit to concrete, without the need to drill a hole first.
-
Quick View
Pegatanke Cold-Welding Epoxy, Black
It is a high quality epoxy glue, developed to withstand the most demanding physical and chemical conditions. Used in industrial, automotive, naval, electrical and construction repairs; as well as in the simplest home repairs, thanks to its high resistance to extreme temperatures and voltage.
EXCELLENT FOR:- Petrol tanks
- Water tanks
- Radiators
- Car repairs
-
Read MoreQuick View
Lag Shield, Long and Short
The Lag Shield is a screw style anchor designed for use with lag bolts. It is suitable for use in concrete and the mortar joints of block or brick walls. In harder masonry materials, short style Lag Shields are used to reduce drilling time. The long style version is used in soft or weak masonry to better develop strength. The Lag Shield is not recommended for overhead or life safety applications.
