BA15 Troffer Clip
Troffer fasteners, or ‘hurricane clips’, give positive support for troffers and lay-in fixtures. Straight lip or upturned lip fixtures fits rectangular or round head T bars.
Complies with NEC 410/16(c) for fixtures supported by suspended ceilings.
- Description
Troffer fasteners, or 'hurricane clips', give positive support for troffers and lay-in fixtures. Straight lip or upturned lip fixtures fits rectangular or round head T bars.
Complies with NEC 410/16(c) for fixtures supported by suspended ceilings.
Related Products
-
Quick ViewPurlin Clamp, 3/8″
Purlin clamps provide structural attachment specifically to the purlins that support a roof. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room.
-
Read MoreQuick ViewCaddy 1-Hole Strap for Conduit
The CPVC One Hole Wrap Around Pipe Strap is designed to support pipe running horizontally on side of a beam, or as a guide to mount CPVC pipe running perpendicular across the top of a beam, or on a vertical run. Model 1070 may be installed onto wood using supplied fastener, or into minimum 20 gauge steel using one 1/4″ x 1 tek screw.
-
Quick View
Elite Beam Clamp
Elite Beam Clamps are used as structural attachments to the top or bottom of metal beams, purlins, channel, or angle iron.
-
Quick View
Standard Riser Clamps (6400)
Model 6400 Standard Riser Clamps from Elite components are designed for copper tube sizes. They are available in carbon steel with Copper colored Epoxy (PC) and in sizes from 1/2″ thru 4″.Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8) -
Quick View
3-Hole Corner Angle L Bracket
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 2-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Read MoreQuick View
Junior Beam Clamp, Plain
Beam clamps provide structural attachment to the flange of metal beams, purlins, channel strut, or angle iron. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room.
-
Quick View
4-Hole Corner Angle L Bracket, Stainless
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 4-1/8″ long, with three 9/16″ holes to secure to struts or other surfaces. Stainless steel material makes this product more rust resistant, and it is suitable for exterior uses where rain or salt water are expected.
-
Quick View
Wide Beam Clamp, Galvanized, Shiny
Beam clamps provide structural attachment to the flange of metal beams, purlins, channel strut, or angle iron. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room. With its galvanized coating, this clamp can also be used in exterior or open building situations.
-
Quick View
Elite Clevis Hanger
A clevis hanger consists of one U-shaped clevis and a second V-shaped clevis with a hole in a flattened section at the base of the V, joined together with a bolt. Clevis hangers are used as a pipe attachment providing vertical adjustment for pipes
-
Read MoreQuick View
Gasket, Full Face, Red Rubber
These gaskets are comprised of red rubber, a copolymer of Styrene and Butadiene, also known as SBR. It feature excellent impact and tensile strength, good resistance to abrasion and easily conforms to uneven flange surfaces.
This Synthetic material was developed as an alternative to Natural Rubber. The red rubber gaskets are recommended for service in cold and hot water, air, steam,and some weak acids. It should not be used with strong acids, oils, grease, and chlorates
