BA12 T-Bar Hanger
The BA12 T-Bar hanger is used to mount electrical boxes above acoustical ceiling tiles. It works with square or octagonal boxes, and allows for flush mounting or 3/4″ offset to accomodate a plaster ring. For additional support, a dropwire can be attached to included box mounting clip.
- Description
The BA12 T-Bar hanger is used to mount electrical boxes above acoustical ceiling tiles. It works with square or octagonal boxes, and allows for flush mounting or 3/4" offset to accomodate a plaster ring. For additional support, a dropwire can be attached to included box mounting clip.
Related Products
-
Wide Beam Clamp, Galvanized, Shiny
Beam clamps provide structural attachment to the flange of metal beams, purlins, channel strut, or angle iron. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room. With its galvanized coating, this clamp can also be used in exterior or open building situations.
-
Read MoreQuick ViewGasket, Ring, Red Rubber
These gaskets are comprised of red rubber, a copolymer of Styrene and Butadiene, also known as SBR. It feature excellent impact and tensile strength, good resistance to abrasion and easily conforms to uneven flange surfaces.
This Synthetic material was developed as an alternative to Natural Rubber. The red rubber gaskets are recommended for service in cold and hot water, air, steam,and some weak acids. It should not be used with strong acids, oils, grease, and chlorates -
Read MoreQuick ViewPost Bases for 1-5/8″ Strut
These three models of a post base provide a secure mounting point for strut. Once properly bolted in place, it is guaranteed not to move. And with six bolt holes on three sides for all models, the strut will be held in place with no chance of slipping out.
Options include having a square base plate, held in place with four bolts (10 hole models), or a smaller rectangular base held down by two bolts (8 hole model). In addition, the 10 hole model can have the strut and plate square to each other, or having the plate at a 45° angle. These various configurations are meant to accommodate your specific needs. -
4-Hole Corner Angle L Bracket, Stainless
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 4-1/8″ long, with three 9/16″ holes to secure to struts or other surfaces. Stainless steel material makes this product more rust resistant, and it is suitable for exterior uses where rain or salt water are expected.
-
Read MoreQuick ViewCaddy Two-Hole Strap for CPVC Pipe
Caddy 2-Hole Strap helps with the installation of CPVC pipe on wood, masonry or other surface when extra load bearing is needed. Its curved shape positively snaps onto the pipe, making installation easier. For indoor or outdoor applications.
-
Elite Loop Hanger
Elite Loop Hangers are the recommended pipe support solution for the suspension of stationary non-insulated pipe lines.
-
U-Bolt Style Beam to Channel Clamp
The U-Bolt style beam-to-channel clamp features a piece of bent plate and a u-bolt that is threaded on both sides to secure a strut in place against a beam. The strut is fed through the u-bolt, which is then tightened to secure both the plate to the beam and the strut to the plate. U-style beam clamps can be used to secure strut to either the underside of the beam or the inside of the beam, depending on the configuration of the clamp.
-
2-Hole Corner Angle L Bracket B
This connector is used for connecting metal struts together, as a 90° angle. The two sides are 2″ and 1-7/8″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance. -
Read MoreQuick View3/8″ Wide Beam Clamp, Plain
Beam clamps provide structural attachment to the flange of metal beams, purlins, channel strut, or angle iron. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room.
-
Standard Riser Clamps (6200-6300)
Model 6200-6300 Standard Riser Clamps from Elite components are designed for standard iron pipe. They are available in either galvanized or plain and in sizes from 1/2″ thru 24″.
Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8)









