Strut, 13/16″, Slotted, HDG
Strut channel, often referred to as Unistrut, is used for light structural support, often for supporting wiring, plumbing, or mechanical components such as air conditioning or ventilation systems.
This piece is half-size at 13/16″ deep, with slots on 2″ centers, and is HDG for great rust protection.
- Additional information
- Description
- Strut Options
Additional information
| Size | 1, 2, 3 |
|---|---|
| Size2 | 4, 5 |
Strut channel, often referred to as Unistrut, is used for light structural support, often for supporting wiring, plumbing, or mechanical components such as air conditioning or ventilation systems.
This piece is half-size at 13/16" deep, with slots on 2" centers, and is HDG for great rust protection.
13/16" X 1-5/8" X 10', 14GA, Slots on 2" Centers
13/16" X 1-5/8" X 20', 14GA, Slots on 2" Centers
13/16" X 1-5/8" X 10', 14GA, Slots on 2" Centers, HDG
13/16" X 1-5/8" X 10', 14GA, Slots on 2" Centers, Stainless Steel
1-5/8" X 1-5/8" X 10', 14GA, Slots on 2" Centers
1-5/8" X 1-5/8" X 20', 14GA, Slots on 2" Centers
1-5/8" X 1-5/8" X 10', 14GA, Slots on 2" Centers, HDG
1-5/8" X 1-5/8" X 10', 12GA Heavy Duty, Slots on 2" Centers
1-5/8" X 1-5/8" X 10', 14GA, Slots on 2" Centers, Stainless Steel
1-5/8" X 1-5/8" X 10', 12GA Heavy Duty, Slots on 2" Centers, Stainless Steel
Related Products
-
Read MoreQuick ViewCaddy 1-Hole Strap for Conduit
The CPVC One Hole Wrap Around Pipe Strap is designed to support pipe running horizontally on side of a beam, or as a guide to mount CPVC pipe running perpendicular across the top of a beam, or on a vertical run. Model 1070 may be installed onto wood using supplied fastener, or into minimum 20 gauge steel using one 1/4″ x 1 tek screw.
-
Read MoreQuick ViewPipe Clamp
A pipe clamp is an attachment which clamps around the pipe to connect it to the remainder of a pipe hanger assembly. Pipe clamps are recommended for the suspension of cold pipe lines and may or may not be insulated.
-
Quick View
Elite Beam Clamp
Elite Beam Clamps are used as structural attachments to the top or bottom of metal beams, purlins, channel, or angle iron.
-
Read MoreQuick View
Clevis Pipe Hanger, HDG
A clevis hanger is a pipe attachment providing vertical adjustment, consisting of a clevis type top bolted to a formed steel bottom strap. They are recommended for the suspension of non-insulated, stationary pipe lines. This clevis hanger has been treated with a hot-dipped galvanized coating, giving it a great rust resistance. It is suitable for any interior use, as well as exterior use.
-
Quick View
2-Hole Offset Z Support
This Z-shaped connector allows the joining of two perpendicular pieces of strut, with the open side of each piece facing the same direction.
-
Quick View
Elite Clevis Hanger
A clevis hanger consists of one U-shaped clevis and a second V-shaped clevis with a hole in a flattened section at the base of the V, joined together with a bolt. Clevis hangers are used as a pipe attachment providing vertical adjustment for pipes
-
Quick View
Elite Loop Hanger
Elite Loop Hangers are the recommended pipe support solution for the suspension of stationary non-insulated pipe lines.
-
Quick View
Concrete Insert Box, Ceiling
The concrete insert box is designed to allow attachment of threaded rod in a ceiling, and is installed before the cement is poured into the wooden form. Once the cement hardens, and the form is removed, the knockout plate is removed and a concrete insert nut is placed inside. The threaded rod is then screwed into the nut, providing support for equipment to be mounted to.
-
Read MoreQuick View
Clevis Pipe Hanger, Galvanized
A clevis hanger is a pipe attachment providing vertical adjustment, consisting of a clevis type top bolted to a formed steel bottom strap. They are recommended for the suspension of non-insulated, stationary pipe lines. These hangers have been given an electroplated galvanized finish which provides general rust resistance, and are suitable for any interior uses.
-
Quick View
Standard Riser Clamps (6200-6300)
Model 6200-6300 Standard Riser Clamps from Elite components are designed for standard iron pipe. They are available in either galvanized or plain and in sizes from 1/2″ thru 24″.
Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8)
