Unistrut Clamp Copper
Unistrut clamps are used to secure pipe and conduit to strut. This piece is copper, for copper pipes.
- Additional information
- Description
Additional information
| Size | 1/4″, 3/8″, 5/8″, 7/8″, 1-1/8″, 1-3/8″, 1-5/8″, 2-1/8″, 2-5/8″, 3-1/8″, 3-5/8″, 4-1/8″, 5-1/8″, 6-1/8″ |
|---|
Unistrut clamps are used to secure pipe and conduit to strut. This piece is electro-galvanized for basic rust protection.
Related Products
-
Quick View4-Hole Corner Angle L Bracket
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 4-1/8″ and 3-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Read MoreQuick ViewConcrete Forms, Econ-O-Sleeve
Econ-O-Sleeve Hole Forms consistently form round, smooth, uniform holes and are available in a broad range of diameters. They may be cut, stacked, or telescoped for any slab thickness.
Form holes, don’t drill em!
Econ-O-Sleeve forms come in a variety of diameters, and adjust for any slab thickness by stacking two or more together. -
Quick View
2-Hole Corner Angle L Bracket B
This connector is used for connecting metal struts together, as a 90° angle. The two sides are 2″ and 1-7/8″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance. -
Quick View
Elite Clevis Hanger
A clevis hanger consists of one U-shaped clevis and a second V-shaped clevis with a hole in a flattened section at the base of the V, joined together with a bolt. Clevis hangers are used as a pipe attachment providing vertical adjustment for pipes
-
Quick View
U-Bolt Style Beam to Channel Clamp
The U-Bolt style beam-to-channel clamp features a piece of bent plate and a u-bolt that is threaded on both sides to secure a strut in place against a beam. The strut is fed through the u-bolt, which is then tightened to secure both the plate to the beam and the strut to the plate. U-style beam clamps can be used to secure strut to either the underside of the beam or the inside of the beam, depending on the configuration of the clamp.
-
Read MoreQuick View
Junior Beam Clamp, Galvanized, Shiny
Beam clamps provide structural attachment to the flange of metal beams, purlins, channel strut, or angle iron. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room. With its galvanized coating, this clamp can also be used in exterior or open building situations. -
Quick View
8-Hole Strut Wing Corner Connector
This connector is used for connecting metal struts together, with the ends of two against a third strut between them. An electro-galvanized coating provides rust resistance.
-
Read MoreQuick View
Gasket, Ring, Red Rubber
These gaskets are comprised of red rubber, a copolymer of Styrene and Butadiene, also known as SBR. It feature excellent impact and tensile strength, good resistance to abrasion and easily conforms to uneven flange surfaces.
This Synthetic material was developed as an alternative to Natural Rubber. The red rubber gaskets are recommended for service in cold and hot water, air, steam,and some weak acids. It should not be used with strong acids, oils, grease, and chlorates -
Quick View
4-Hole Closed 45 Degree Angle Connector
This connector is used for connecting metal struts together, at a 45° angle. The two sides are 3-1/2″ and 4-1/8″ long, with four 9/16″ holes to secure it to struts, or other surfaces. An electro-galvanized coating provides rust resistance.
-
Quick View
3-Hole Corner Angle L Bracket, Stainless
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 2-1/2″ long, with three 9/16″ holes to secure to struts or other surfaces. Stainless steel material makes this product more rust resistant, and it is suitable for exterior uses where rain or salt water are expected.
