4-Hole Corner Angle L Bracket, Stainless
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 4-1/8″ long, with three 9/16″ holes to secure to struts or other surfaces. Stainless steel material makes this product more rust resistant, and it is suitable for exterior uses where rain or salt water are expected.
- Description
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2" and 4-1/8" long, with three 9/16" holes to secure to struts or other surfaces. Stainless steel material makes this product more rust resistant, and it is suitable for exterior uses where rain or salt water are expected.
Related Products
-
Read MoreQuick ViewJunior Beam Clamp, Galvanized, Shiny
Beam clamps provide structural attachment to the flange of metal beams, purlins, channel strut, or angle iron. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room. With its galvanized coating, this clamp can also be used in exterior or open building situations. -
Quick View3-Hole Corner Angle L Bracket
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 2-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Read MoreQuick ViewCaddy 1-Hole Strap for Conduit
The CPVC One Hole Wrap Around Pipe Strap is designed to support pipe running horizontally on side of a beam, or as a guide to mount CPVC pipe running perpendicular across the top of a beam, or on a vertical run. Model 1070 may be installed onto wood using supplied fastener, or into minimum 20 gauge steel using one 1/4″ x 1 tek screw.
-
Read MoreQuick ViewCaddy Stand-Off Strap, 2-Hole for Conduit
Two-hole stand-off straps are used for mounting CPVC pipe to a wall, ceiling, or other surface. They eliminate the need for wood blocks under the pipe. They position the pipe 1-1/2″ off the surface.
-
Read MoreQuick ViewGasket, Ring, Red Rubber
These gaskets are comprised of red rubber, a copolymer of Styrene and Butadiene, also known as SBR. It feature excellent impact and tensile strength, good resistance to abrasion and easily conforms to uneven flange surfaces.
This Synthetic material was developed as an alternative to Natural Rubber. The red rubber gaskets are recommended for service in cold and hot water, air, steam,and some weak acids. It should not be used with strong acids, oils, grease, and chlorates -
Read MoreQuick ViewConcrete Forms, Econ-O-Sleeve
Econ-O-Sleeve Hole Forms consistently form round, smooth, uniform holes and are available in a broad range of diameters. They may be cut, stacked, or telescoped for any slab thickness.
Form holes, don’t drill em!
Econ-O-Sleeve forms come in a variety of diameters, and adjust for any slab thickness by stacking two or more together. -
Quick View4-Hole Closed 45 Degree Angle Connector
This connector is used for connecting metal struts together, at a 45° angle. The two sides are 3-1/2″ and 4-1/8″ long, with four 9/16″ holes to secure it to struts, or other surfaces. An electro-galvanized coating provides rust resistance.
-
Quick View2-Hole Corner Angle L Bracket B
This connector is used for connecting metal struts together, as a 90° angle. The two sides are 2″ and 1-7/8″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance. -
Quick ViewElite Copper Loop Hanger
Elite Copper Loop Hangers are required for hanging copper pipe and allows for vertical adjustment of pipe after installation.
-
Quick ViewStandard Riser Clamps (6200-6300)
Model 6200-6300 Standard Riser Clamps from Elite components are designed for standard iron pipe. They are available in either galvanized or plain and in sizes from 1/2″ thru 24″.
Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8)
