4-Hole Closed 45 Degree Angle Connector
This connector is used for connecting metal struts together, at a 45° angle. The two sides are 3-1/2″ and 4-1/8″ long, with four 9/16″ holes to secure it to struts, or other surfaces. An electro-galvanized coating provides rust resistance.
- Description
This connector is used for connecting metal struts together, at a 45° angle. The two sides are 3-1/2" and 4-1/8" long, with four 9/16" holes to secure it to struts, or other surfaces. An electro-galvanized coating provides rust resistance.
Related Products
-
Quick ViewStandard Riser Clamps (6200-6300)
Model 6200-6300 Standard Riser Clamps from Elite components are designed for standard iron pipe. They are available in either galvanized or plain and in sizes from 1/2″ thru 24″.
Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8)
-
Quick View
Elite Clevis Hanger
A clevis hanger consists of one U-shaped clevis and a second V-shaped clevis with a hole in a flattened section at the base of the V, joined together with a bolt. Clevis hangers are used as a pipe attachment providing vertical adjustment for pipes
-
Read MoreQuick View
Caddy Stand-Off Strap, 2-Hole for Conduit
Two-hole stand-off straps are used for mounting CPVC pipe to a wall, ceiling, or other surface. They eliminate the need for wood blocks under the pipe. They position the pipe 1-1/2″ off the surface.
-
Read MoreQuick View
Post Bases for 1-5/8″ Strut
These three models of a post base provide a secure mounting point for strut. Once properly bolted in place, it is guaranteed not to move. And with six bolt holes on three sides for all models, the strut will be held in place with no chance of slipping out.
Options include having a square base plate, held in place with four bolts (10 hole models), or a smaller rectangular base held down by two bolts (8 hole model). In addition, the 10 hole model can have the strut and plate square to each other, or having the plate at a 45° angle. These various configurations are meant to accommodate your specific needs. -
Read MoreQuick View
Caddy 1-Hole Strap for Conduit
The CPVC One Hole Wrap Around Pipe Strap is designed to support pipe running horizontally on side of a beam, or as a guide to mount CPVC pipe running perpendicular across the top of a beam, or on a vertical run. Model 1070 may be installed onto wood using supplied fastener, or into minimum 20 gauge steel using one 1/4″ x 1 tek screw.
-
Quick View
2-Hole Corner Angle L Bracket A
This connector is used for connecting metal struts together, as a 90° angle. The two sides are 2-1/4″ and 1-5/8″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Quick View
3-Hole Corner Angle L Bracket
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 2-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Quick View
Elite Copper Loop Hanger
Elite Copper Loop Hangers are required for hanging copper pipe and allows for vertical adjustment of pipe after installation.
-
Quick View
Elite Beam Clamp
Elite Beam Clamps are used as structural attachments to the top or bottom of metal beams, purlins, channel, or angle iron.
-
Quick View
Wide Beam Clamp, Galvanized, Shiny
Beam clamps provide structural attachment to the flange of metal beams, purlins, channel strut, or angle iron. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room. With its galvanized coating, this clamp can also be used in exterior or open building situations.
