Cylindrical Head Socket Cap Screw
Socket cap screws have a small cylindrical head with tall vertical sides, and with recessed hex-shaped sockets with which to drive them. Because they are driven with hex keys (Allen wrench) or hex socket bits, they are ideal for applications where limited clearance would not allow the use of wrenches and sockets. In addition, the driving surface is protected from external damage and provides six sides of contact surface for added torque.
- Additional information
- Description
Additional information
| Material/Finish | Alloy, Black Oxide, Stainless Steel |
|---|---|
| Diameter | #0, #1, #2, #3, #4, #5, #6, #8, #10, #12, 1/4″, 5/16″, 3/8″, 7/16″, 1/2″, 9/16″, 5/8″, 3/4″, 7/8″, 1″, 1″-14, 1″-12, 1-1/8″, 1-1/4″, 1-3/8″, 1-1/2″, 1-3/4″, 2″, 2-1/4″, 2-1/2″ |
| Threading | Coarse, Fine |
| Length | 1/16″, 3/32″, 1/8″, 5/32″, 11/64″, 3/16″, 7/32″, 1/4″, 9/32″, 5/16″, 11/32″, 3/8″, 7/16″, 15/32″, 1/2″, 9/16″, 5/8″, 11/16″, 3/4″, 13/16″, 15/16″, 7/8″, 1″, 1-1/8″, 1-3/16″, 1-1/4″, 1-5/16″, 1-3/8″, 1-7/16″, 1-1/2″, 1-9/16″, 1-5/8″, 1-3/4″, 1-7/8″, 2″, 2-1/8″, 2-1/4″, 2-5/16″, 2-3/8″, 2-1/2″, 2-5/8″, 2-3/4″, 2-7/8″, 3″, 3-1/4″, 3-1/2″, 3-3/4″, 4″, 4-1/4″, 4-3/8″, 4-1/2″, 4-3/4″, 5″, 5-1/4″, 5-1/2″, 5-3/4″, 6″, 6-1/4, 6-1/2″, 6-3/4″, 7″, 7-1/4, 7-1/2″, 8″, 8-1/2″, 9″, 9-1/2″, 10″, 10-1/2″, 11″, 11-1/2″, 12″, 13″, 14″, 15″, 16″, 17″, 18″, 20″ |
Socket cap screws have a small cylindrical head with tall vertical sides, and with recessed hex-shaped sockets with which to drive them. Because they are driven with hex keys (Allen wrench) or hex socket bits, they are ideal for applications where limited clearance would not allow the use of wrenches and sockets. In addition, the driving surface is protected from external damage and provides six sides of contact surface for added torque.
Related Products
-
Read MoreQuick ViewDekfast Roof Screws, 10″ to 18″
Dekfast XHD High Strength Fasteners are ideal for insulation attachment to wood and light gauge steel. The SD#1 point cuts through gravel, BUR and metal up to 18ga. Black Sentri SP long=life coating provides extended corrosion protection. The #3PH pan head is compatible with all Dekfast insulation stress and membrane seam plates.
Longer sizes are available by special request.
FM and Dade County Approved. -
Quick ViewPanelMate Quick Kit
This kit contains all of the hardware you need to get started making your home hurricane-resistant. There are 40 PanelMate anchors, along with the bit and driver to properly set them. There are also 40 washers and wing nuts to secure the storm panels to the anchors.
-
Read MoreQuick View
Fender Washers
-
Read MoreQuick View
T-Nuts
T-nuts are barrel shaped fasteners with internal threading, and are used to provide an anchor point for a bolt in a piece of wood, whether a flat board or a dimensional piece. They are especially useful when a flush surface is wanted. T-nuts have a flat base with prongs bent up at 90° angles, parallel to the barrel. After pre-drilling a hole, the t-nut can be fixed in place either by tightening a bolt into it from the top, which pulls the prongs into the wood, or using hammer to pound the locking prongs into the wood until flush.
-
Read MoreQuick View
Set Screws, Cup Point
Set Screws are essentially a headless bolt, which has a hex socket in the driving end. They are commonly used when a protruding head would be in the way of other moving parts. Their most common function is to secure two parts together, but without a pre-determined positioning point between them. A prime example is fixing a pulley wheel along a drive shaft, where the set screw in the wheel’s hub is tightened into the side of the drive shaft and holds them tight due strictly to friction.
Set screws are available either as a black hard steel alloy, or as stainless steel.
Because of its headless shape, and how it bores through its hole, a set screw is also known as a “grub screw”.
-
Read MoreQuick View
Carriage Bolts
Carriage bolts have a smooth rounded head with a square neck underneath that locks into wood to prevent spinning when tightened. Use with a pre-drilled hole and secure with a hex nut and washer. They are great fasteners for decks, play equipment, docks, fencing, and furniture.
The unique design is great for connections where the head is not accessible for tightening. The self-locking square neck and coarse threads fasten very securely.
All carriage bolts we stock have coarse threading as a standard. -
Read MoreQuick View
Hex Nuts
Hex nuts in all their forms are widely used in construction and manufacturing. There are many different styles of hex nuts, including finished hex nuts, acorn nuts, lock nuts, and heavy hex nuts. They are available in many different grades of metal, with different finishes, and with coarse or fine threads. Choose from the options below to find the right hex nut for your project.
Note: The Coupling Nut – Reducing items use the Inch – Special option because they have two sizes of threads.
-
Read MoreQuick View
F-Track Bolts
The square head of these F-Track Bolts fits perfectly into all flat and angled storm panel F-Track.
-
Read MoreQuick View
Pro-Tect System for Pool Enclosures
PRO-TECT Fastener Protection System consists of a nylon sleeve and a cap that, together, cover and protect the anchor screw. The PRO-TECT nylon sleeve gives protection from electrolysis, providing worry-free installation while extending the life of the product. This is very important for the harsh conditions of the coastal environments and extreme temperatures.
The PRO-TECT cap snaps onto the top of the nylon sleeve, covering the head of the Blue-Tap anchor screw. Due to its special design, the cap will not come off easily. Caps are available in White and Bronze.
By repelling water and preventing penetration, PRO-TECT reduces or eliminates the need for warranty work, increasing life expectancy of the structures. -
Read MoreQuick View
Flat Washers, USS & SAE
