Wej-It Inject-TITE Fast Set Epoxy
Inject-TITE FS (Fast-Set) is a 2-component, 1:1 mix ration, structural epoxy system that offers exceptional strength in anchoring and doweling applications. Tested in accordance with ASTM E488 and ASTM E1512 for its capability to resist static, dynamic, seismic and wind loads in uncracked concrete for both threaded rod and rebar.
- Additional information
- Description
- Advantages and Installation
- Warnings and Pullout Strength Charts
- Data Sheets & Downloads
Additional information
| Item | Epoxy, 10 Oz Tube, Epoxy, 22 Oz Tube, Wej-It Epoxy Nozzle |
|---|
Inject-TITE FS (Fast-Set) is a 2-component, 1:1 mix ration, structural epoxy system that offers exceptional strength in anchoring and doweling applications. Tested in accordance with ASTM E488 and ASTM E1512 for its capability to resist static, dynamic, seismic and wind loads in uncracked concrete for both threaded rod and rebar.
Other uses for Wej-It Inject-TITE FS epoxy include short and long term tensile anchoring, including wind, seismic and shear forces in accordance with allowable stress design (ASD), grouting dowel bars and tie bars for full depth concrete pavement repairs, and as a bonding agent for fresh-to-hardened concrete, and hardened-to-hardened concrete.
Advantages & Features
- Available in numerous cartridge sizes and in bulk
- Moisture insensitive allowing installation and curing in damp environments
- Withstands freeze-thaw conditions
- Little or no odor
- High modulus
- In-service temperature range between 35 °F (2 °C) and 180 °F (82 °C)
Installation Instructions
Limitations & Warnings:
- Do not thin with solvents, as this may affect cure
- Not recommended for any overhead application where there may be a sustained tensile load
- For anchoring applications, concrete must be a minimum of 21 days old prior to anchor installation
- Performance characteristics, such as seismic and long term load resistance, were tested in accordance with ASTM E488-96 (2003) & E1512-01 (2015) provisions and not that of ACI 355.4, and are therefore not applicable in the concrete tension zone - always consult with a design professional prior to use to ensure product applicability
- Smooth bulk formulation has not been tested to ASTM E488 or ASTM E1512
Technical Information
Related Products
-
Quick ViewHammer Drive Tool
Drive pin anchors are installed in pre-drilled holes. Using this tool and a hammer, a solid strike drives a nail into the anchor body, expanding the anchor to form a tight fit. These anchors secure light loads to masonry materials.
-
Read MoreQuick ViewAnchor Setting Tool Powder Load, .22 Caliber
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .22 caliber powder loads provide the force needed to drive those fasteners into place. This level is the lightest available, for smaller fasteners and thinner materials.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick ViewHammer Drive Pins
Drive pin anchors are installed in pre-drilled holes with a hammer strike that drives a nail into the anchor body, expanding the anchor to form a tight fit. These anchors secure light loads to masonry materials.
-
Read MoreQuick ViewThreaded Stud
Threaded studs are available in a variety of thread and shank lengths for use in concrete, some types of concrete block, and A36 or A572 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required or for suspending sprinkler systems.
The threaded studs have a specially designed point to allow proper penetration into the base material. A plastic flute is mounted over the point to retain the drive pin in the fasteners guide of the tool providing guidance during the driving operation. A plastic cap is also provided to protect the threads of the fastener during the driving process as well as providing guidance during installation. -
Read MoreQuick ViewLead Machine Screw Anchor
The lead machine screw anchor is an internally threaded anchor designed to make female threads into concrete. It features a soft lead shell on the outside and steel threads on the inside. They are designed for solid concrete but can be installed into hollow block or brick with a special setting tool.
-
Read MoreQuick ViewLag Shield, Long and Short
The Lag Shield is a screw style anchor designed for use with lag bolts. It is suitable for use in concrete and the mortar joints of block or brick walls. In harder masonry materials, short style Lag Shields are used to reduce drilling time. The long style version is used in soft or weak masonry to better develop strength. The Lag Shield is not recommended for overhead or life safety applications.
-
Read MoreQuick ViewKnurled Track Pin
The Ramset 3/4 in. Drive Pins are ideal for fastening track in concrete and can be used to penetrate dense concrete and structural-quality steel. The pins are specifically fabricated for toughness and durability.
-
Read MoreQuick ViewRamset Washer Pin Fastening Systems
Designed to drive flush into steel and concrete
Consistent and optimum quality in every pin
Washer increases bearing surface against material -
Read MoreQuick ViewPlastic Anchor Kit
This kit contains standard drywall/concrete expansion anchors, screws, and a masonry drill bit sized appropriately.
Kits are available with standard Phillips pan head screws, or with slotted hex head washer screws.
Sizes are:
3/16″ Anchor & Bit, with #6 – #8 x 3/4″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Slot Hex Head Screw -
Quick ViewPegatanke Cold-Welding Epoxy, Black
It is a high quality epoxy glue, developed to withstand the most demanding physical and chemical conditions. Used in industrial, automotive, naval, electrical and construction repairs; as well as in the simplest home repairs, thanks to its high resistance to extreme temperatures and voltage.
EXCELLENT FOR:- Petrol tanks
- Water tanks
- Radiators
- Car repairs
