Teardrop Hanger, Stainless Steel
Teardrop hangers are designed to anchor stationary, non-insulated pipes to overhead structure. This piece is made from stainless steel for excellent rust protection.
Stainless steel teardrop hangers do not come with a knurled nut. Instead, standard practice is to use a stainless steel washer and two stainless steel nuts. Simply position the threaded rod through the two holes on the strap ends, place the washer over the threaded rod, and tighten the two nuts onto the threaded rod. Nuts and washers are available separately.
- Additional information
- Description
- Loads and Dimensions Chart
Additional information
| Size | 1/2″, 3/4″, 1″, 1-1/4″, 1-1/2″, 2″, 2-1/2″, 3″, 3-1/2″, 4″, 5″, 6″, 8″ |
|---|
Teardrop hangers are designed to anchor stationary, non-insulated pipes to overhead structure. This piece is made from stainless steel for excellent rust protection.
Stainless steel teardrop hangers do not come with a knurled nut. Instead, standard practice is to use a stainless steel washer and two stainless steel nuts. Simply position the threaded rod through the two holes on the strap ends, place the washer over the threaded rod, and tighten the two nuts onto the threaded rod. Nuts and washers are available separately.
Related Products
-
Quick ViewStandard Riser Clamps (6400)
Model 6400 Standard Riser Clamps from Elite components are designed for copper tube sizes. They are available in carbon steel with Copper colored Epoxy (PC) and in sizes from 1/2″ thru 4″.Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8) -
Read MoreQuick View
Caddy Stand-Off Strap, 2-Hole for Conduit
Two-hole stand-off straps are used for mounting CPVC pipe to a wall, ceiling, or other surface. They eliminate the need for wood blocks under the pipe. They position the pipe 1-1/2″ off the surface.
-
Quick View
4-Hole Open Angle Connector
This connector is used for connecting two piece of strut, at an open 45° angle, also called 135° angle.
-
Quick View
Elite Loop Hanger
Elite Loop Hangers are the recommended pipe support solution for the suspension of stationary non-insulated pipe lines.
-
Quick View
2-Hole Offset Z Support
This Z-shaped connector allows the joining of two perpendicular pieces of strut, with the open side of each piece facing the same direction.
-
Read MoreQuick View
Caddy 1-Hole Strap for Conduit
The CPVC One Hole Wrap Around Pipe Strap is designed to support pipe running horizontally on side of a beam, or as a guide to mount CPVC pipe running perpendicular across the top of a beam, or on a vertical run. Model 1070 may be installed onto wood using supplied fastener, or into minimum 20 gauge steel using one 1/4″ x 1 tek screw.
-
Read MoreQuick View
Clevis Pipe Hanger, Stainless Steel
A clevis hanger is a pipe attachment providing vertical adjustment, consisting of a clevis type top bolted to a formed steel bottom strap. They are recommended for the suspension of non-insulated, stationary pipe lines. This clevis hanger is made from stainless steel, giving it superb rust resistance. It is suitable for any interior use, as well as exterior use.
-
Read MoreQuick View
Pipe Clamp
A pipe clamp is an attachment which clamps around the pipe to connect it to the remainder of a pipe hanger assembly. Pipe clamps are recommended for the suspension of cold pipe lines and may or may not be insulated.
-
Read MoreQuick View
Clevis Pipe Hanger, Plain
A clevis hanger is a pipe attachment providing vertical adjustment, consisting of a clevis type top bolted to a formed steel bottom strap. They are recommended for the suspension of non-insulated, stationary pipe lines. These hangers have a natural, or plain, black finish, and are suitable for any interior uses.
-
Quick View
Concrete Insert Box, Ceiling, Galvanized
The concrete insert box is designed to allow attachment of threaded rod in a ceiling, and is installed before the cement is poured into the wooden form. Once the cement hardens, and the form is removed, the knockout plate is removed and a concrete insert nut is placed inside. The threaded rod is then screwed into the nut, providing support for equipment to be mounted to.
This version of this equipment is galvanized, and can be used in interior or exterior placements.
