Sammys Threaded Rod Hanger for Wood, Vertical
The SAMMYS threaded rod hanger is designed to install vertically into the bottom of wood structures, providing a secure anchor for either 1/4″ or 3/8″ threaded rod. The screw itself is from the ITWBuildex line of wood screws, for a proven secure hold with no pre-drilling required.
SAMMYS anchors are designed to be installed with the Black Installation Tool, to ensure proper torque and prevent over-tightening.
- Additional information
- Description
- Loads and Dimensions Chart
Additional information
| Size | 3/8″-16 Rod, 1/4 x 2″ Screw, 1/4″-20 Rod, 1/4 x 2″ Screw, 3/8″-16 Rod, 1/4 x 2″ Screw, Stainless Steel, 3/8″-16 Rod, 1/4 x 3″ Screw |
|---|
The SAMMYS threaded rod hanger is designed to install vertically into the bottom of wood structures, providing a secure anchor for either 1/4" or 3/8" threaded rod. The screw itself is from the ITWBuildex line of wood screws, for a proven secure hold with no pre-drilling required.
SAMMYS anchors are designed to be installed with the Black Installation Tool, to ensure proper torque and prevent over-tightening.
Related Products
-
Quick ViewElite Loop Hanger
Elite Loop Hangers are the recommended pipe support solution for the suspension of stationary non-insulated pipe lines.
-
Read MoreQuick ViewConcrete Insert Nut
The concrete insert nut is specifically made to fit inside a concrete insert box, which was embedded in the cement ceiling when it was poured. The insert nut allows threaded rod to be suspended, for the mounting of equipment.
-
Quick ViewElite Clevis Hanger
A clevis hanger consists of one U-shaped clevis and a second V-shaped clevis with a hole in a flattened section at the base of the V, joined together with a bolt. Clevis hangers are used as a pipe attachment providing vertical adjustment for pipes
-
Quick ViewElite Beam Clamp
Elite Beam Clamps are used as structural attachments to the top or bottom of metal beams, purlins, channel, or angle iron.
-
Quick View3-Hole Corner Plate
This basic plate connector can be used to secure two pieces of strut together, at a 90° angle.
-
Read MoreQuick ViewCeiling Flange, Plain
Ceiling flanges are used to secure threaded rod to a ceiling, so that equipment can be attached to the threaded rod. These flanges are designed to either support 3/8″-16 rod, or 1/2″-13 rod. They have a natural, plain finish, and are excellent choice for interior use.
-
Read MoreQuick ViewSteel Eye Socket
Steel eye sockets are designed to attached hanging threaded rod to structures. Connectors, supports, and equipment can then be attached to the threaded rod as usual.
-
Read MoreQuick ViewCaddy Stand-Off Strap, 2-Hole for Conduit
Two-hole stand-off straps are used for mounting CPVC pipe to a wall, ceiling, or other surface. They eliminate the need for wood blocks under the pipe. They position the pipe 1-1/2″ off the surface.
-
Quick View4-Hole Open Angle Connector
This connector is used for connecting two piece of strut, at an open 45° angle, also called 135° angle.
-
Quick ViewPipe Roof Support, Pipe Prop APS-2
The APS-2 from Pipe Prop is the standard in adjustable pipe support systems for industry professionals. The durability and reliability of a Pipe Prop product sets it apart as where homemade pipe systems are unpredictable at best.
The APS-2 serves pipes up to 2.5″ in width or smaller and allows you to determine your own heigh using 3/4” Schedule 40 PVC Electrical Conduit (cut required).
The APS-2 comes with 1 base, 1 saddle, and 1 nylon strap for securing your pipe to the saddle.
