- Additional information
- Description
- Features
- Loads & Dimensions Chart
Additional information
| Sizes | 3/16″ x 1″, 1/4″ x 1″ |
|---|
The Hammer-Set anchor is a mechanical drive anchor consisting of a zinc die cast expansion body and zinc plated steel expander drive pin. Hammer-Set anchors are medium-duty anchors designed for a variety of fastening applications in concrete, block, and brick. Use Hammer-Set anchors to attach termination bars, drywall track, electrical boxes and clips, flashing, lumber and more.
- Works in concrete, block, and brick
- Great for fastening electric boxes, conduit clips, roof flashing, plywood and 2 x lumber
- Fast, easy installation
- Install through material to be fastened
- Ideal for light-duty and tamper-resistant applications
- Low profile mushroom head
- For indoor and outdoor use
- Not for use in overhead applications
Related Products
-
Hot
Quick ViewAnkr-TITE® CCAT Cracked Concrete Wedge Anchors
The CCAT Cracked Concrete Wedge Anchors are engineered to provide superior performance in cracked concrete in both seismic and wind load conditions.
-
Quick View1-1/4″ Ceiling Clip Assembly
The Ramset Ceiling Clip is designed to mount into a slanted ceiling, with hanging wire attached through the eye. Able to support light loads such as suspended ceiling grids.
-
Read MoreQuick ViewRamset Fastening Pins
The Ramset Fastening System Drive Pins are powder actuated pins used to attach material to concrete or steel. The pins are specifically fabricated for toughness and durability.
The 1/2″ and 5/8″ pins are knurled for extra grip, and are specifically engineered for use in structural-quality steel.
The 3/4″ and 1″ pins are perfect for attaching metal track to concrete.
The 1″ up to 2″ pins are sized for attaching furring strips or plywood to concrete.
The 2-1/2″ and 3″ pins are designed to attach 2×4’s to concrete. -
Read MoreQuick ViewAnchor Setting Tool Powder Load Strips
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These color coordinated .25 and .27 caliber powder loads provide the force needed to drive those fasteners into place. They provide from medium power up to the highest power of loads available.
Each strip has 10 powder loads, and there are 10 strips per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator’s manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick ViewLead Hammer Drive Anchor
The Hammer-Set anchor is a mechanical drive anchor consisting of a zinc die cast expansion body and zinc plated steel expander drive pin. Hammer-Set anchors are medium-duty anchors designed for a variety of fastening applications in concrete, block, and brick. It is ideal for light-duty and tamper-resistant applications. Use Hammer-Set anchors to attach termination bars, drywall track, electrical boxes and clips, flashing, lumber and more.
-
Read MoreQuick ViewGrey Plastic Anchor, w/Lip
This is a standard plastic expansion anchor that can be used in drywall or solid walls for light hanging or attaching needs.
-
Read MoreQuick ViewGrey Plastic Anchor, No Lip
This is a standard plastic expansion anchor that can be used in drywall or solid walls for light hanging or attaching needs. This type has no outer ring or lip that remains outside the pre-drilled hole, so there will not be any plastic visible once the screw is in place. Also, whatever is being attached to the wall will sit directly against the wall, with no gap.
-
Read MoreQuick ViewToggle Wing, Zinc Plated
A Toggle spring wing anchor, also called a toggle nut, in zinc plated steel is an anchor used in hollow wall applications (walls with space on the other side) such as drywall and concrete blocks (also called cinder blocks) or any hollow concrete masonry unit. Toggle wings are often used to replace spring wings used in the installations of toggle bolts. Toggle nuts are used with machine screws through pre-drilled holes.
-
Quick ViewPegatanke Cold-Welding Epoxy, Clear
PEGETANKE® Transparent, is a high quality epoxy adhesive, designed for those jobs where no traces of adhesive use should be left, giving a more esthetic finish. PEGETANKE® Transparent is the only one in its kind with high resistance to tension and high temperatures.
EXCELLENT FOR:- Goggles
- Headlights
- Translucent materials
- Glass
-
Read MoreQuick ViewHammer Drive Pins
Drive pin anchors are installed in pre-drilled holes with a hammer strike that drives a nail into the anchor body, expanding the anchor to form a tight fit. These anchors secure light loads to masonry materials.
