Hex Cap Screws, Grades 2
A hex cap screw is a six-sided bolt with a trimmed hex head and a washer face on the bearing surface. Informally, it is also called a Finished Hex Bolt. Hex cap screws have tighter tolerances than standard bolts of the same size, and so are often used where precise tolerances are needed. The standard hex screw specifications include ASTM A449 and SAE J429 Grade-2.
- Additional information
- Description
Additional information
| Threading | Coarse |
|---|---|
| Material/Finish | HDG, Stainless 18-8, Stainless 316, Zinc |
| Diameter | 1/4″, 5/16″, 3/8″, 7/16″, 1/2″, 9/16″, 5/8″, 3/4″, 7/8″, 1″, 1-1/8″, 1-1/4″, 1-1/2″ |
| Length | 3/8″, 1/2″, 5/8″, 3/4″, 7/8″, 1″, 1-1/8″, 1-1/4″, 1-3/8″, 1-1/2″, 1-5/8″, 1-3/4″, 1-7/8″, 2″, 2-1/4″, 2-3/8″, 2-1/2″, 2-3/4″, 3″, 3-1/4″, 3-1/2″, 3-3/4″, 4″, 4-1/4″, 4-1/2″, 4-3/4″, 5″, 5-1/4″, 5-1/2″, 5-3/4″, 6″, 6-1/2″, 7″, 7-1/2″, 8″, 8-1/2″, 9″, 9-1/2″, 10″, 11″, 12″, 13″, 14″, 15″, 16″, 18″, 20″, 24″ |
A hex cap screw is a six-sided bolt with a trimmed hex head and a washer face on the bearing surface. Informally, it is also called a Finished Hex Bolt. Hex cap screws have tighter tolerances than standard bolts of the same size, and so are often used where precise tolerances are needed. The standard hex screw specifications include ASTM A449 and SAE J429 Grade-2
Related Products
-
Read MoreQuick ViewSidewalk Bolt, Stainless Steel
Also known as shutter screws, the ultra-wide truss head distributes the load over a large area for excellent holding pressure when placing plywood, metal, and fabric hurricane panels or removable track. Made of 18-8 stainless steel, these screws are chemical resistant and may be mildly magnetic.
-
Read MoreQuick ViewPlow Bolts
Plow bolts feature a countersunk, flat head, square neck, and unified thread pitch. They are commonly used in road graders, scoop shovels, and other heavy-duty industrial equipment where a flat, smooth surface is required. Grade-5 plow bolts are made from a medium-grade, heat-treated carbon steel, and have a plain finish.
-
Read MoreQuick View
T-Nuts
T-nuts are barrel shaped fasteners with internal threading, and are used to provide an anchor point for a bolt in a piece of wood, whether a flat board or a dimensional piece. They are especially useful when a flush surface is wanted. T-nuts have a flat base with prongs bent up at 90° angles, parallel to the barrel. After pre-drilling a hole, the t-nut can be fixed in place either by tightening a bolt into it from the top, which pulls the prongs into the wood, or using hammer to pound the locking prongs into the wood until flush.
-
Read MoreQuick View
Hex Tap Bolts
The major distinguishing feature of hex tap bolts is that they are always fully threaded from under the head to the tip, no matter the size. Other features, such as chamfered point or washer bearing surface under the head, may be present, or may not. Tap bolts are meant to be used nuts to secure two objects together, but they also will fully seat into a tapped hole to secure one material to a base material.
They are available in Grade 2, Grade 5, and in Stainless Steel. -
Read MoreQuick View
Wing Nuts
Wing nuts are a type of specialty nut with a pair of wings to enable it to tighten without tools. The wings provide a grip for the thumb and finger for turning. They are commonly used where frequent adjustments or removals are needed, and can be made quickly at a later stage.
An alternative form of the wing nut has a washer built in, and is used to storm-proof the windows of a building. This washer face allows the wing nut to be used to secure plywood onto fixed anchors, where the hole in the plywood will be larger than the anchor studs it and the wing nut are being mounted on. This provides the advantage of having a larger surface bearing the pressure, while also eliminating the need of a separate washer that will often fall and get lost during storm-prep installation. -
Read MoreQuick View
Set Screws, Cup Point
Set Screws are essentially a headless bolt, which has a hex socket in the driving end. They are commonly used when a protruding head would be in the way of other moving parts. Their most common function is to secure two parts together, but without a pre-determined positioning point between them. A prime example is fixing a pulley wheel along a drive shaft, where the set screw in the wheel’s hub is tightened into the side of the drive shaft and holds them tight due strictly to friction.
Set screws are available either as a black hard steel alloy, or as stainless steel.
Because of its headless shape, and how it bores through its hole, a set screw is also known as a “grub screw”.
-
Quick View
Buildex Trugrip Roof Screw, 1″
Buildex® TrueGrip timber screws are suitable for fixing metal roofing into both hardwood and softwood timber battens. Their sharp point prevents screw-walking when starting to insert them. They also engage the material faster, and need less effort, for a safer installation environment.
-
Quick View
Aluminum Key Hole Washer
Aluminum key-hole washers are commonly used with combo truss machine screws and sidewalk bolts. They are used as an additional backing plate when storm panels keyways do not line up correctly. They are also often used to provide additional backing when sidewalk bolts have been changed out to truss head screws. They can be placed on after panels are installed.
-
Read MoreQuick View
Lock Washers
-
Read MoreQuick View
Mro Thread-Locker, 50ml Bottle
MRO Solutions thread-locking products are anaerobic compounds formulated for sealing, joining, fastening, retaining, and generally locking together metal components. Unlike other thread-lockers, MRO compounds are non-surface sensitive, so they do not require use of primers for curing.
Once parts are mated with MRO thread-lockers, they form a unitized assembly that resists vibration. In addition, the mated parts are sealed against attack from corrosion, internal rust, seizure, solvents, gases, and other chemicals.
