Carriage Bolts
Carriage bolts have a smooth rounded head with a square neck underneath that locks into wood to prevent spinning when tightened. Use with a pre-drilled hole and secure with a hex nut and washer. They are great fasteners for decks, play equipment, docks, fencing, and furniture.
The unique design is great for connections where the head is not accessible for tightening. The self-locking square neck and coarse threads fasten very securely.
All carriage bolts we stock have coarse threading as a standard.
- Additional information
- Description
- Threads Per Inch
Additional information
| Material/Finish | Grade 5, Stainless, HDG, Zinc |
|---|---|
| Diameter | 1/4″, 5/16″, 3/8″, 7/16″, 1/2″, 5/8″, 3/4″, #10, 7/8″ |
| Length | 1/4″, 1/2″, 5/8″, 3/4″, 7/8″, 1″, 1-1/4″, 1-1/2″, 1-3/4″, 2″, 2-1/4″, 2-1/2″, 2-3/4″, 3″, 3-1/4″, 3-1/2″, 3-3/4″, 4″, 4-1/4″, 4-1/2″, 5″, 5-1/4″, 5-1/2″, 6″, 6-1/2″, 7″, 7-1/2″, 8″, 8-1/2″, 9″, 9-1/2″, 10″, 10-1/2″, 11″, 11-1/2″, 12″, 12-1/2″, 13″, 14″, 14-1/2″, 15″, 16″, 18″, 20″, 21-1/2″, 24″ |
Carriage bolts have a smooth rounded head with a square neck underneath that locks into wood to prevent spinning when tightened. Use with a pre-drilled hole and secure with a hex nut and washer. They are great fasteners for decks, play equipment, docks, fencing, and furniture.
The unique design is great for connections where the head is not accessible for tightening. The self-locking square neck and coarse threads fasten very securely.
All carriage bolts we stock have coarse threading as a standard.
1/4"-20
5/16"-18
3/8:-16
7/16"-14
1/2"-13
5/8"-11
3/4"-10
Related Products
-
Read MoreQuick ViewFender Washers
-
Read MoreQuick View
Dekfast Roof Screws, 10″ to 18″
Dekfast XHD High Strength Fasteners are ideal for insulation attachment to wood and light gauge steel. The SD#1 point cuts through gravel, BUR and metal up to 18ga. Black Sentri SP long=life coating provides extended corrosion protection. The #3PH pan head is compatible with all Dekfast insulation stress and membrane seam plates.
Longer sizes are available by special request.
FM and Dade County Approved. -
Read MoreQuick View
T-Nuts
T-nuts are barrel shaped fasteners with internal threading, and are used to provide an anchor point for a bolt in a piece of wood, whether a flat board or a dimensional piece. They are especially useful when a flush surface is wanted. T-nuts have a flat base with prongs bent up at 90° angles, parallel to the barrel. After pre-drilling a hole, the t-nut can be fixed in place either by tightening a bolt into it from the top, which pulls the prongs into the wood, or using hammer to pound the locking prongs into the wood until flush.
-
Read MoreQuick View
Lock Washers
-
Read MoreQuick View
DRYWALL SCREWS
Drywall screws fasten sheets of drywall (also called sheetrock or plasterboard) to the wall or ceiling support studs. Drywall screws with coarse threads are used to to attach to wood framing. Screws with fine threading are used for metal studs. Also, self-drilling versions are available for attaching to thicker metal support.
Most drywall screws have a tapered bugle head to penetrate the drywall without damaging the outer layer of paper. Trim head screws are used to attach trim pieces over the drywall, and have a very small head that disappears into the surface for easy finishing. K-lath screws have a large wafer head to easily attach wire mesh, or lath, to the frame studs to support plaster. Their low profile heads are easily covered over by the finished surface of tile, stone, brick, stucco, etc. -
Read MoreQuick View
Machine Screws
Machine screws are meant to hold two metal work pieces together, with the use of a threaded pre-tapped hole, or through a hole and held with a nut. They are threaded the entire length of the shank. For most styles of a machine screw, the length is measured from under the head to the end of the screw. For flat head machine screws, since they are intended to fit into a countersunk hole, their length is measured from the top of the screw head to the end of the screw.
-
Read MoreQuick View
Wood Screws
Wood screws are made to join two pieces of wood together and securely hold them. There are many styles of wood screws available today, from various driver tools to what material the wood screw is made from.
-
Read MoreQuick View
Cylindrical Head Socket Cap Screw
Socket cap screws have a small cylindrical head with tall vertical sides, and with recessed hex-shaped sockets with which to drive them. Because they are driven with hex keys (Allen wrench) or hex socket bits, they are ideal for applications where limited clearance would not allow the use of wrenches and sockets. In addition, the driving surface is protected from external damage and provides six sides of contact surface for added torque.
-
Read MoreQuick View
Anchor Bolts, L-Bolts
-
Quick View
Buildex Trugrip Roof Screw, 1″
Buildex® TrueGrip timber screws are suitable for fixing metal roofing into both hardwood and softwood timber battens. Their sharp point prevents screw-walking when starting to insert them. They also engage the material faster, and need less effort, for a safer installation environment.
