4-Hole Splice Plate
The 4-hole splice plate allows two pieces of strut to be connected together for secure alignment and stability. The struts can be positioned either end-to-end, or two pieces against a perpendicular piece between them, or three pieces side-by-side.
- Description
The 4-hole splice plate allows two pieces of strut to be connected together for secure alignment and stability. The struts can be positioned either end-to-end, or two pieces against a perpendicular piece between them, or three pieces side-by-side.
Related Products
-
Quick View3-Hole Corner Angle L Bracket, Stainless
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 2-1/2″ long, with three 9/16″ holes to secure to struts or other surfaces. Stainless steel material makes this product more rust resistant, and it is suitable for exterior uses where rain or salt water are expected.
-
Quick View2-Hole Corner Angle L Bracket B
This connector is used for connecting metal struts together, as a 90° angle. The two sides are 2″ and 1-7/8″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance. -
Read MoreQuick ViewGasket, Ring, Red Rubber
These gaskets are comprised of red rubber, a copolymer of Styrene and Butadiene, also known as SBR. It feature excellent impact and tensile strength, good resistance to abrasion and easily conforms to uneven flange surfaces.
This Synthetic material was developed as an alternative to Natural Rubber. The red rubber gaskets are recommended for service in cold and hot water, air, steam,and some weak acids. It should not be used with strong acids, oils, grease, and chlorates -
Quick ViewElite Copper Loop Hanger
Elite Copper Loop Hangers are required for hanging copper pipe and allows for vertical adjustment of pipe after installation.
-
Quick View2-Hole Closed 45 Degree Angle Connector
This connector is used for connecting metal struts together, at a 45° angle. The two sides are 3-1/2″ and 2-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Quick ViewU-Bolt Style Beam to Channel Clamp
The U-Bolt style beam-to-channel clamp features a piece of bent plate and a u-bolt that is threaded on both sides to secure a strut in place against a beam. The strut is fed through the u-bolt, which is then tightened to secure both the plate to the beam and the strut to the plate. U-style beam clamps can be used to secure strut to either the underside of the beam or the inside of the beam, depending on the configuration of the clamp.
-
Quick View8-Hole Strut Wing Corner Connector
This connector is used for connecting metal struts together, with the ends of two against a third strut between them. An electro-galvanized coating provides rust resistance.
-
Quick View4-Hole Closed 45 Degree Angle Connector
This connector is used for connecting metal struts together, at a 45° angle. The two sides are 3-1/2″ and 4-1/8″ long, with four 9/16″ holes to secure it to struts, or other surfaces. An electro-galvanized coating provides rust resistance.
-
Read MoreQuick ViewCaddy 1-Hole Strap for Conduit
The CPVC One Hole Wrap Around Pipe Strap is designed to support pipe running horizontally on side of a beam, or as a guide to mount CPVC pipe running perpendicular across the top of a beam, or on a vertical run. Model 1070 may be installed onto wood using supplied fastener, or into minimum 20 gauge steel using one 1/4″ x 1 tek screw.
-
Quick View4-Hole Corner Angle L Bracket, Stainless
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 4-1/8″ long, with three 9/16″ holes to secure to struts or other surfaces. Stainless steel material makes this product more rust resistant, and it is suitable for exterior uses where rain or salt water are expected.
