1/2″ Combo Bit for 1/4″ Lead M/S Anchor
This 1/2″ combo drill bit installs lead anchors for 1/4″-20 combo sidewalk bolts. I works for all masonry surfaces, both block and concrete. The smaller pilot bit starts the hole in the right location, and the larger 1/2″ step bit drills the perfect hole for setting lead machine screw anchors.
Fully adjustable collar allows you to set the depth of the hole for a perfect set every-time. Comes with Hex Wrench.
- Description
This 1/2" combo drill bit installs lead anchors for 1/4"-20 combo sidewalk bolts. I works for all masonry surfaces, both block and concrete. The smaller pilot bit starts the hole in the right location, and the larger 1/2" step bit drills the perfect hole for setting lead machine screw anchors.
Fully adjustable collar allows you to set the depth of the hole for a perfect set every-time. Comes with Hex Wrench.
Related Products
-
Read MoreQuick ViewDeWalt Wood Knockers II
DeWalt Wood-Knocker concrete inserts are installed onto wooden forms used to support newly poured concrete floor slabs, roof slabs or walls. When the forms are stripped, the color-coded flange is visibly embedded in the concrete surface. The inserts allow the attachment of steel threaded rod or threaded bolts in sizes ranging from 1/4″ to 3/4″ in diameter. The hex impact plate offers resistance to rotation within the concrete as a steel threaded rod or threaded bolt is being installed.
-
Read MoreQuick ViewAnchor Setting Tool Powder Load, .22 Caliber
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .22 caliber powder loads provide the force needed to drive those fasteners into place. This level is the lightest available, for smaller fasteners and thinner materials.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick View
Hollow Wall Anchor, Long and Short
The sleeve type hollow wall anchor is designed for use in base materials such as plaster, wallboard, concrete block, hollow tile or plywood. It is installed using a drill and can be used with various wall thicknesses. The sections of the sleeve expand as the screw is tightened and driven into the wall. The front section of the hollow wall anchor will add permanent screw threads, so that once set, the screw may be removed as often as necessary without affecting the anchor.
These anchors are also known as Molly bolts. -
Read MoreQuick View
Grey Plastic Anchor, No Lip
This is a standard plastic expansion anchor that can be used in drywall or solid walls for light hanging or attaching needs. This type has no outer ring or lip that remains outside the pre-drilled hole, so there will not be any plastic visible once the screw is in place. Also, whatever is being attached to the wall will sit directly against the wall, with no gap.
-
Read MoreQuick View
E-Z Anchor Drywall Anchors
The E-Z Ancor is a one-piece self-drilling anchor designed for optimal holding performance in drywall. Because it pre-drills its own small precise hole, no hole preparation is necessary.
With a range of choices, including mini, regular and heavy duty, and available in zinc or nylon, there is an E-Z solution to your hanging problems. -
Read MoreQuick View
Plastic Anchor Kit
This kit contains standard drywall/concrete expansion anchors, screws, and a masonry drill bit sized appropriately.
Kits are available with standard Phillips pan head screws, or with slotted hex head washer screws.
Sizes are:
3/16″ Anchor & Bit, with #6 – #8 x 3/4″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Slot Hex Head Screw -
Read MoreQuick View
Lead Machine Screw Anchor
The lead machine screw anchor is an internally threaded anchor designed to make female threads into concrete. It features a soft lead shell on the outside and steel threads on the inside. They are designed for solid concrete but can be installed into hollow block or brick with a special setting tool.
-
Read MoreQuick View
Nylon Round Head Nail-In
-
Read MoreQuick View
Pipe Spike
Powers Pipe SPIKE® is ideal for ceiling applications where hanging threaded rod is needed.
The SPIKE® anchor is a patented, one-piece, tamper-proof vibration resistant anchor for use in concrete, block, brick or stone. Several head styles and anchor materials are available. The SPIKE® anchor is formed with an “s” shaped configuration at the working end of the anchor to create an expansion mechanism. Since the anchor is pre-expanded, there is no secondary tightening operation required which greatly reduces the overall cost of an anchor installation. -
Read MoreQuick View
Toggle Wing, Zinc Plated
A Toggle spring wing anchor, also called a toggle nut, in zinc plated steel is an anchor used in hollow wall applications (walls with space on the other side) such as drywall and concrete blocks (also called cinder blocks) or any hollow concrete masonry unit. Toggle wings are often used to replace spring wings used in the installations of toggle bolts. Toggle nuts are used with machine screws through pre-drilled holes.
