Hex Cap Screws, Grades 2
A hex cap screw is a six-sided bolt with a trimmed hex head and a washer face on the bearing surface. Informally, it is also called a Finished Hex Bolt. Hex cap screws have tighter tolerances than standard bolts of the same size, and so are often used where precise tolerances are needed. The standard hex screw specifications include ASTM A449 and SAE J429 Grade-2.
- Additional information
- Description
Additional information
| Threading | Coarse |
|---|---|
| Material/Finish | HDG, Stainless 18-8, Stainless 316, Zinc |
| Diameter | 1/4″, 5/16″, 3/8″, 7/16″, 1/2″, 9/16″, 5/8″, 3/4″, 7/8″, 1″, 1-1/8″, 1-1/4″, 1-1/2″ |
| Length | 3/8″, 1/2″, 5/8″, 3/4″, 7/8″, 1″, 1-1/8″, 1-1/4″, 1-3/8″, 1-1/2″, 1-5/8″, 1-3/4″, 1-7/8″, 2″, 2-1/4″, 2-3/8″, 2-1/2″, 2-3/4″, 3″, 3-1/4″, 3-1/2″, 3-3/4″, 4″, 4-1/4″, 4-1/2″, 4-3/4″, 5″, 5-1/4″, 5-1/2″, 5-3/4″, 6″, 6-1/2″, 7″, 7-1/2″, 8″, 8-1/2″, 9″, 9-1/2″, 10″, 11″, 12″, 13″, 14″, 15″, 16″, 18″, 20″, 24″ |
A hex cap screw is a six-sided bolt with a trimmed hex head and a washer face on the bearing surface. Informally, it is also called a Finished Hex Bolt. Hex cap screws have tighter tolerances than standard bolts of the same size, and so are often used where precise tolerances are needed. The standard hex screw specifications include ASTM A449 and SAE J429 Grade-2
Related Products
-
Read MoreQuick ViewFlat Washers, USS & SAE
-
Read MoreQuick View
T-Nuts
T-nuts are barrel shaped fasteners with internal threading, and are used to provide an anchor point for a bolt in a piece of wood, whether a flat board or a dimensional piece. They are especially useful when a flush surface is wanted. T-nuts have a flat base with prongs bent up at 90° angles, parallel to the barrel. After pre-drilling a hole, the t-nut can be fixed in place either by tightening a bolt into it from the top, which pulls the prongs into the wood, or using hammer to pound the locking prongs into the wood until flush.
-
Quick View
Aluminum Key Hole Washer
Aluminum key-hole washers are commonly used with combo truss machine screws and sidewalk bolts. They are used as an additional backing plate when storm panels keyways do not line up correctly. They are also often used to provide additional backing when sidewalk bolts have been changed out to truss head screws. They can be placed on after panels are installed.
-
Read MoreQuick View
Square Plate Washer
Square plate washers are made from low carbon steel and have a larger surface area than round washers. Since they develop more friction when tightened against wood, they are often found in timber construction.
Often, square plate washers are used to attach treated lumber sill plates to concrete foundations. Another common use is using square plate washers to attach wood beams to the walls of a garage, and them mount the garage door rails and equipment. -
Read MoreQuick View
Pro-Tect System for Pool Enclosures
PRO-TECT Fastener Protection System consists of a nylon sleeve and a cap that, together, cover and protect the anchor screw. The PRO-TECT nylon sleeve gives protection from electrolysis, providing worry-free installation while extending the life of the product. This is very important for the harsh conditions of the coastal environments and extreme temperatures.
The PRO-TECT cap snaps onto the top of the nylon sleeve, covering the head of the Blue-Tap anchor screw. Due to its special design, the cap will not come off easily. Caps are available in White and Bronze.
By repelling water and preventing penetration, PRO-TECT reduces or eliminates the need for warranty work, increasing life expectancy of the structures. -
Read MoreQuick View
Hex Cap Screws, Grades 8
A hex cap screw is a six-sided bolt with a trimmed hex head and a washer face on the bearing surface. Informally, it is also called a Finished Hex Bolt. Hex cap screws have tighter tolerances than standard bolts of the same size, and so are often used where precise tolerances are needed. The standard hex screw specifications include ASTM A449 and SAE J429 Grade-8.
-
Read MoreQuick View
DRYWALL SCREWS
Drywall screws fasten sheets of drywall (also called sheetrock or plasterboard) to the wall or ceiling support studs. Drywall screws with coarse threads are used to to attach to wood framing. Screws with fine threading are used for metal studs. Also, self-drilling versions are available for attaching to thicker metal support.
Most drywall screws have a tapered bugle head to penetrate the drywall without damaging the outer layer of paper. Trim head screws are used to attach trim pieces over the drywall, and have a very small head that disappears into the surface for easy finishing. K-lath screws have a large wafer head to easily attach wire mesh, or lath, to the frame studs to support plaster. Their low profile heads are easily covered over by the finished surface of tile, stone, brick, stucco, etc. -
Read MoreQuick View
Carriage Bolts
Carriage bolts have a smooth rounded head with a square neck underneath that locks into wood to prevent spinning when tightened. Use with a pre-drilled hole and secure with a hex nut and washer. They are great fasteners for decks, play equipment, docks, fencing, and furniture.
The unique design is great for connections where the head is not accessible for tightening. The self-locking square neck and coarse threads fasten very securely.
All carriage bolts we stock have coarse threading as a standard. -
Quick View
PanelMate Quick Kit
This kit contains all of the hardware you need to get started making your home hurricane-resistant. There are 40 PanelMate anchors, along with the bit and driver to properly set them. There are also 40 washers and wing nuts to secure the storm panels to the anchors.
-
Read MoreQuick View
All Thread, Threaded Rod
Threaded rod has continuous threading, either on both ends or it may extend along the complete length of the rod. It has no head or fashioned tip. Threaded rod can be used as an anchor bolt, clamp, hanger or U-bolt.
Threaded rod is available in carbon steel, as Plain, Zinc Plated and HDG, as well as Stainless Steel and the B7/A193 alloy.
