C6+ Ceramic Epoxy, Max Strength
For The Most Demanding Jobs Red Head C6+ is the highest strength adhesive in our history. Designed for use in the most demanding anchoring applications, the maximum strength of Red Head C6+ is backed by ICC-ES approvals for both concrete and masonry. It is also the only adhesive approved for core-drilled holes in cracked concrete without the use of a roughening tool.
C6+ Epoxy is available in 15oz and 30oz sizes.
- Additional information
- Description
- Data Charts
- Data Sheets & Downloads
Additional information
| Size | 15 Oz., 30 Oz. |
|---|
Red Head C6+ is the highest strength adhesive in our history. Designed for use in the most demanding anchoring applications, the maximum strength of Red Head C6+ is backed by ICC-ES approvals for both concrete and masonry. It is also the only adhesive approved for core-drilled holes in cracked concrete without the use of a roughening tool.
C6+ Epoxy is available in 15oz and 30oz sizes.
- At least 25% stronger than the old C6+ formulation for threaded rod in cracked concrete with seismic conditions
- Fastest Cure time in its class, curing in just 2.75 hours at 90°F and in only 2 hours at 110°F!
- ICC-ES approved for cracked concrete and seismic applications (ICC-ES ESR 4046)
- ICC-ES approved for masonry applications (ICC-ES ESR 4109)
- ICC-ES Approved for use in core-drill holes, even in cracked concrete
- At least 10 minutes of nozzle life (10 min working time at 110F)
- Can be used down to 40°F and up to 110°F
- Can be used in oversized holes
- Rugged cartridges resist breakage due to rough handling or cold temperatures
- 24-month shelf life
- 2:1 Mix Ratio
Related Products
-
Read MoreQuick ViewLag Shield, Long and Short
The Lag Shield is a screw style anchor designed for use with lag bolts. It is suitable for use in concrete and the mortar joints of block or brick walls. In harder masonry materials, short style Lag Shields are used to reduce drilling time. The long style version is used in soft or weak masonry to better develop strength. The Lag Shield is not recommended for overhead or life safety applications.
-
Read MoreQuick ViewRamset Washer Pin Fastening Systems
Designed to drive flush into steel and concrete
Consistent and optimum quality in every pin
Washer increases bearing surface against material -
HotQuick View
Ankr-TITE® CCAT Cracked Concrete Wedge Anchors
The CCAT Cracked Concrete Wedge Anchors are engineered to provide superior performance in cracked concrete in both seismic and wind load conditions.
-
HotQuick View
Original Wej-It® Wedge Anchors
The Wej-It original Wedge Anchors are time tested with proven reliabilty and has been an industry standard for over 60 years.
-
Quick View
Hammer Drive Tool
Drive pin anchors are installed in pre-drilled holes. Using this tool and a hammer, a solid strike drives a nail into the anchor body, expanding the anchor to form a tight fit. These anchors secure light loads to masonry materials.
-
Quick View
1″ Conduit Clip w/Pin
Designed for use with Powder Actuated tools, this EMT clip will secure conduit to concrete, without the need to drill a hole first.
-
Read MoreQuick View
Anchor Setting Tool Powder Load, .22 Caliber
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .22 caliber powder loads provide the force needed to drive those fasteners into place. This level is the lightest available, for smaller fasteners and thinner materials.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick View
Ramset Fastening Pins
The Ramset Fastening System Drive Pins are powder actuated pins used to attach material to concrete or steel. The pins are specifically fabricated for toughness and durability.
The 1/2″ and 5/8″ pins are knurled for extra grip, and are specifically engineered for use in structural-quality steel.
The 3/4″ and 1″ pins are perfect for attaching metal track to concrete.
The 1″ up to 2″ pins are sized for attaching furring strips or plywood to concrete.
The 2-1/2″ and 3″ pins are designed to attach 2×4’s to concrete. -
Read MoreQuick View
Grey Plastic Anchor, w/Lip
This is a standard plastic expansion anchor that can be used in drywall or solid walls for light hanging or attaching needs.
-
Read MoreQuick View
Anchor Setting Tool Powder Load, 25 Caliber Disc
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .25 caliber powder loads provide the force needed to drive those fasteners into place. This level is the medium strength available, for average fasteners and materials.
Each disc has 10 powder loads, and there are 10 discs per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders.
