Anchor Setting Tool Powder Load Strips
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These color coordinated .25 and .27 caliber powder loads provide the force needed to drive those fasteners into place. They provide from medium power up to the highest power of loads available.
Each strip has 10 powder loads, and there are 10 strips per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator’s manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders.
- Additional information
- Description
- Power Levels
- Training and Certification
- Data Sheets & Downloads
Additional information
| Power Level | 2 Brown, 27 Caliber, 3 Green, 25 Calliber, 3 Green, 27 Caliber, 4 Yellow, 25 Caliber, 4 Yellow, 27 Caliber, 5 Red, 25 Caliber, 5 Red, 27 Caliber, 6 Purple, 27 Caliber |
|---|
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These color coordinated .25 and .27 caliber powder loads provide the force needed to drive those fasteners into place. This provides from medium power up to the highest power available.
Each strip has 10 powder loads, and there are 10 strips per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders.
ONLINE POWDER TRAINING AND CERTIFICATION
To protect the operator and assure safety on the jobsite, OSHA and ANSI require all powder actuated tool users to be trained
and certified for the tool that will be used. Ramset enables you to receive training thrrough our website training program.
This approach combines interactive web-based training techniques and online testing with feedback during the test.
The course consists of approximately 30 pages of usage, safety, and troubleshooting material. Upon completion of this
brief course, you will immediately take an online exam. With successful completion of the exam, you then print a Ramset
certification card.
At the end of the course, you are also given the ability to download individual tool manuals.
To take the course, and be certified to operate a Ramset powder actuated tool:
• Go to www.Ramset.com
• Find the heading called Get Your License
• Click P.A.T. Licensing
• Click Begin Operator Course (choose English / Spanish / French)
• When course is complete, take the test
• After passing the test, download and print your certificate
• Place the certificate in your wallet
Related Products
-
Read MoreQuick ViewPipe Spike
Powers Pipe SPIKE® is ideal for ceiling applications where hanging threaded rod is needed.
The SPIKE® anchor is a patented, one-piece, tamper-proof vibration resistant anchor for use in concrete, block, brick or stone. Several head styles and anchor materials are available. The SPIKE® anchor is formed with an “s” shaped configuration at the working end of the anchor to create an expansion mechanism. Since the anchor is pre-expanded, there is no secondary tightening operation required which greatly reduces the overall cost of an anchor installation. -
Read MoreQuick ViewHammer Drive Pins
Drive pin anchors are installed in pre-drilled holes with a hammer strike that drives a nail into the anchor body, expanding the anchor to form a tight fit. These anchors secure light loads to masonry materials.
-
Read MoreQuick ViewRamset Fastening Pins
The Ramset Fastening System Drive Pins are powder actuated pins used to attach material to concrete or steel. The pins are specifically fabricated for toughness and durability.
The 1/2″ and 5/8″ pins are knurled for extra grip, and are specifically engineered for use in structural-quality steel.
The 3/4″ and 1″ pins are perfect for attaching metal track to concrete.
The 1″ up to 2″ pins are sized for attaching furring strips or plywood to concrete.
The 2-1/2″ and 3″ pins are designed to attach 2×4’s to concrete. -
Quick View1″ Conduit Clip w/Pin
Designed for use with Powder Actuated tools, this EMT clip will secure conduit to concrete, without the need to drill a hole first.
-
Read MoreQuick ViewToggle Bolt, Zinc Plated
The Toggle Bolt is a spring wing type hollow wall anchor designed for use in block, wallboard and other hollow base materials. The Toggle Bolt is a two-part assembly consisting of a machine screw and a spring wing toggle. Sizes range from 1/8″ x 2″ to 1/2″ x 6″ with combo round, flat, mushroom, tie-wire or slotted hex head styles.
-
Read MoreQuick ViewThreaded Stud
Threaded studs are available in a variety of thread and shank lengths for use in concrete, some types of concrete block, and A36 or A572 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required or for suspending sprinkler systems.
The threaded studs have a specially designed point to allow proper penetration into the base material. A plastic flute is mounted over the point to retain the drive pin in the fasteners guide of the tool providing guidance during the driving operation. A plastic cap is also provided to protect the threads of the fastener during the driving process as well as providing guidance during installation. -
Read MoreQuick ViewRamset Washer Pin Fastening Systems
Designed to drive flush into steel and concrete
Consistent and optimum quality in every pin
Washer increases bearing surface against material -
Read MoreQuick ViewAnchor Setting Tool Powder Load, 25 Caliber Disc
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .25 caliber powder loads provide the force needed to drive those fasteners into place. This level is the medium strength available, for average fasteners and materials.
Each disc has 10 powder loads, and there are 10 discs per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick ViewKnurled Track Pin
The Ramset 3/4 in. Drive Pins are ideal for fastening track in concrete and can be used to penetrate dense concrete and structural-quality steel. The pins are specifically fabricated for toughness and durability.
-
Hot
Quick ViewAnkr-TITE® CCAT Cracked Concrete Wedge Anchors
The CCAT Cracked Concrete Wedge Anchors are engineered to provide superior performance in cracked concrete in both seismic and wind load conditions.
