BH6-F12 Z-Purlin Rod Hanger
The BH6-H7 angle bracket is used to secure wire or 3/8″ rod, to mount equipment, conduit, or ductwork below. Its added section allows mounting it from the angled lip of a metal Z-shaped purlin beam.
- Description
The BH6-H7 angle bracket is used to secure wire or 3/8" rod, to mount equipment, conduit, or ductwork below. Its added section allows mounting it from the angled lip of a metal Z-shaped purlin beam.
Related Products
-
Read MoreQuick View
Clevis Pipe Hanger, PVC Coated Copper
A clevis hanger is a pipe attachment providing vertical adjustment, consisting of a clevis type top bolted to a formed steel bottom strap. They are recommended for the suspension of non-insulated, stationary pipe lines. A PVC coating prevents electrolysis between the pipe and the hanger, and it reduces transmitted noise and vibration.
-
Read MoreQuick View
Concrete Insert Nut
The concrete insert nut is specifically made to fit inside a concrete insert box, which was embedded in the cement ceiling when it was poured. The insert nut allows threaded rod to be suspended, for the mounting of equipment.
-
4-Hole Corner Plate
This basic plate connector can be used to secure three pieces of strut together, with the ends of two pieces against a third strut between them.
-
Read MoreQuick View
Ceiling Flange, Copper
Ceiling flanges are used to secure threaded rod to a ceiling, so that equipment can be attached to the threaded rod. These flanges are designed to either support 3/8″-16 rod, or 1/2″-13 rod. They have a copper finish, and are excellent choice for interior open ceiling situations where their color will complement other equipment.
-
Read MoreQuick View
Caddy Two-Hole Strap for CPVC Pipe
Caddy 2-Hole Strap helps with the installation of CPVC pipe on wood, masonry or other surface when extra load bearing is needed. Its curved shape positively snaps onto the pipe, making installation easier. For indoor or outdoor applications.
-
Standard Riser Clamps (6400)
Model 6400 Standard Riser Clamps from Elite components are designed for copper tube sizes. They are available in carbon steel with Copper colored Epoxy (PC) and in sizes from 1/2″ thru 4″.Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8) -
Read MoreQuick View
Ceiling Flange
Ceiling flanges are used to secure threaded rod to a ceiling, so that equipment can be attached to the threaded rod. These flanges are designed to either support 3/8″-16 rod, or 1/2″-13 rod. An electro-galvanized coating provides rust resistance., and are an excellent choice for any interior use, or in a covered open building space.
-
Read MoreQuick View
Pipe Clamp
A pipe clamp is an attachment which clamps around the pipe to connect it to the remainder of a pipe hanger assembly. Pipe clamps are recommended for the suspension of cold pipe lines and may or may not be insulated.
-
Read MoreQuick View
Clevis Pipe Hanger, HDG
A clevis hanger is a pipe attachment providing vertical adjustment, consisting of a clevis type top bolted to a formed steel bottom strap. They are recommended for the suspension of non-insulated, stationary pipe lines. This clevis hanger has been treated with a hot-dipped galvanized coating, giving it a great rust resistance. It is suitable for any interior use, as well as exterior use.
-
Read MoreQuick View
Caddy 1-Hole Strap for Conduit
The CPVC One Hole Wrap Around Pipe Strap is designed to support pipe running horizontally on side of a beam, or as a guide to mount CPVC pipe running perpendicular across the top of a beam, or on a vertical run. Model 1070 may be installed onto wood using supplied fastener, or into minimum 20 gauge steel using one 1/4″ x 1 tek screw.