3-Hole Splice Plate
The 3-hole splice plate allows pieces of strut to be connected together for basic alignment and stability. The struts can be positioned either two pieces end-to-end, or two pieces against a perpendicular piece between them, or three pieces side-by-side.
- Description
The 3-hole splice plate allows two pieces of strut to be connected together for basic alignment and stability. The struts can be positioned either end-to-end, or two pieces against a perpendicular piece between them, or three pieces side-by-side.
Related Products
-
Quick ViewPurlin Clamp, 3/8″
Purlin clamps provide structural attachment specifically to the purlins that support a roof. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room.
-
Read MoreQuick ViewPost Bases for 1-5/8″ Strut
These three models of a post base provide a secure mounting point for strut. Once properly bolted in place, it is guaranteed not to move. And with six bolt holes on three sides for all models, the strut will be held in place with no chance of slipping out.
Options include having a square base plate, held in place with four bolts (10 hole models), or a smaller rectangular base held down by two bolts (8 hole model). In addition, the 10 hole model can have the strut and plate square to each other, or having the plate at a 45° angle. These various configurations are meant to accommodate your specific needs. -
Read MoreQuick ViewGasket, Ring, Red Rubber
These gaskets are comprised of red rubber, a copolymer of Styrene and Butadiene, also known as SBR. It feature excellent impact and tensile strength, good resistance to abrasion and easily conforms to uneven flange surfaces.
This Synthetic material was developed as an alternative to Natural Rubber. The red rubber gaskets are recommended for service in cold and hot water, air, steam,and some weak acids. It should not be used with strong acids, oils, grease, and chlorates -
Quick View4-Hole Closed 45 Degree Angle Connector
This connector is used for connecting metal struts together, at a 45° angle. The two sides are 3-1/2″ and 4-1/8″ long, with four 9/16″ holes to secure it to struts, or other surfaces. An electro-galvanized coating provides rust resistance.
-
Quick ViewElite Loop Hanger
Elite Loop Hangers are the recommended pipe support solution for the suspension of stationary non-insulated pipe lines.
-
Read MoreQuick ViewCaddy Stand-Off Strap, 2-Hole for Conduit
Two-hole stand-off straps are used for mounting CPVC pipe to a wall, ceiling, or other surface. They eliminate the need for wood blocks under the pipe. They position the pipe 1-1/2″ off the surface.
-
Read MoreQuick ViewJunior Beam Clamp, Galvanized, Shiny
Beam clamps provide structural attachment to the flange of metal beams, purlins, channel strut, or angle iron. Most commonly used to attach threaded rod used to support HVAC duct-work, lights, and other hardware in the open or closed ceiling space of a room. With its galvanized coating, this clamp can also be used in exterior or open building situations. -
Quick View4-Hole Corner Angle L Bracket
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 4-1/8″ and 3-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Quick ViewStandard Riser Clamps (6200-6300)
Model 6200-6300 Standard Riser Clamps from Elite components are designed for standard iron pipe. They are available in either galvanized or plain and in sizes from 1/2″ thru 24″.
Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8)
-
Quick View4-Hole Corner Angle L Bracket, Stainless
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 4-1/8″ long, with three 9/16″ holes to secure to struts or other surfaces. Stainless steel material makes this product more rust resistant, and it is suitable for exterior uses where rain or salt water are expected.
