Sleeve-TITE Sleeve Expansion Anchors
Sleeve-TITE Expansion Anchors come fully assembled and ready to use. This speeds installation and eliminates the p
roblem of missing components. Sleeve-TITE is suitable for a wide variety of applications and available with acorn or hex nut, or flat head, or with rod coupling.
Can be used with almost any material, including:
- Normal Weight Concrete
- Lightweight Concrete
- Hollow Masonry
- Solid Masonry
- Description
- Additional information
- Installation
- Tech Specs
- Part Numbers
- Specifications and Approvals
- Downloads
Description
- Fully assembled and ready to use
- Speeds installation
- Eliminates the problem of missing components
- Suitable for a wide variety of applications
- Available with acorn or hex nut, or flat head, or with rod coupling
Additional information
| Size | Acorn, 1/4” x 1-3/8”, Acorn, 1/4” x 2-1/4”, Hex, 5/16” x 1-1/2”, Hex, 5/16” x 2-1/2”, Hex, 3/8” x 1-7/8”, Hex, 3/8” x 3”, Hex, 3/8” x 4”, Hex, 1/2” x 2-1/4”, Hex, 1/2” x 3”, Hex, 1/2” x 4”, Hex, 1/2” x 6”, Hex, 5/8” x 2-1/4”, Hex, 5/8 x 3”, Hex, 5/8” x 4-1/4”, Hex, 5/8” x 6”, Hex, 3/4” x 2-1/2”, Hex, 3/4” x 4”, Hex, 3/4” x 6-1/4”, Coupling, 3/8” x 1-7/8”, Coupling, 1/2” x 2-1/4”, Flat, 1/4” x 2”, Flat, 1/4” x 3”, Flat, 3/8” x 4”, Flat, 3/8” x 5”, Flat, 3/8” x 6”, Flat, 1/4” x 3”, Stainles Steel, Flat, 3/8” x 3”, 304, Stainles Steel, Flat, 3/8” x 4”, 304, Stainles Steel, Hex, 3/8” x 1-7/8”, 303, Stainles Steel, Hex, 3/8” x 3”, 303, Stainles Steel, Hex, 1/2” x 3”, 303, Stainles Steel, Hex, 1/2” x 4”, 303, Stainles Steel |
|---|
Installation Instructions
- Drill the hole, whose diameter equals the anchor diameter, perpendicular to the work surface. To assure full holding power, do not ream the hole or allow the drill to wobble.
- Drill the hole deeper than the intended embedment, but not closer than two diameters to the opposite surface of the concrete.
- A clean hole is necessary for proper performance. Clean the hole using a nylon brush and compressed air.
- Assemble the nut and washer so that the top of the nut is flush with the top of the anchor. Drive the anchor through the material to be fastened so that the nut and washer are flush with the surface of the material.
- Tighten the nut, or head, 3 to 5 turns past the hand tight position. Installing the "Ankr-TITE® Series" of anchors with a torque wrench is recommended for optimum performance. Refer to adjacent chart.*
NOTE: Always wear safety glasses. Follow drill manufacturer's instructions. Use only solid carbide-tipped drill bits meeting ANSI B212.15 diameter standards.
Can be used with almost any material, including:
- Normal Weight Concrete
- Lightweight Concrete
- Solid Masonry
<a href="https://threadsource.com/wp-content/uploads/2016/02/Sleeve-TITE_Tech_Data.pdf" rel="">Sleeve-TITE Tech Data</a>
<a href="https://threadsource.com/wp-content/uploads/2016/02/Sleeve-TITE_Tech_Manual.pdf" rel="">Sleeve-TITE Tech Manual</a>
Related Products
-
Read MoreQuick ViewSDS Bits for Drop-In Anchor
SDS Drill bits designed to produce the perfect depth of hole for mini drop-in anchors.
These bits are made in the USA, and feature a solid hardened steel body design with premium carbide braised in the tip. They also have a wide shoulder to prevent drilling too deep and hitting rebar or high tension wires, and an innovative dust removal design for fast drilling. -
Read MoreQuick ViewPOWER-Skru Bolt Anchors
The POWER-Skru Bolt Anchor is a high-strength screw anchorwith self-taping threads that offer a unique undercutting design for anchoring into concrete and masonry. No secondary setting is needed. The POWER-Skru Bolt Anchor provides high-strength performance with low installation torque. A heavy-duty mechanically-galvanized finish is available to enhance corrosion resistance.
Can be used with almost any material, including:
- Racking
- Railing Sill
- Stadium Seating
- Tilt up Braces
- Formwork
- Anchoring Equipment
-
Hot
Quick ViewHex Head Cap Screws – Grade 2
Hex Head Cap Screws are designed for easy assembly into a tapped hole. Hex Cap Screws meet SAE specifications with a specially designed washer face under the head and a chamfered point. Plain finish, or bare metal, will have a coating of light oil to resist corrosion. Grade 2 is generally an economical but lower strength fastener.
-
Hot
Quick ViewAnkr-TITE Wej-It Anchors
This anchor is a high-strength, fully threaded, and torque-controlled expansion anchor designed for anchoring into normal-weight concrete, lightweight concrete, and grouted concrete masonry.
-
Hot
Quick ViewHex Head Cap Screws – Grade 5
Hex Head Cap Screws are designed for easy assembly into a tapped hole. Hex Cap Screws meet SAE specifications with a specially designed washer face under the head and a chamfered point. Grade 5 is the most common grade used in manufacturing assembly. Zinc plating, retards the corrosion rate in a normal atmosphere. Tensile Strength: 120,000 psi minimum. -
Quick ViewElite Clevis Hanger
A clevis hanger consists of one U-shaped clevis and a second V-shaped clevis with a hole in a flattened section at the base of the V, joined together with a bolt. Clevis hangers are used as a pipe attachment providing vertical adjustment for pipes
-
Read MoreQuick ViewPro-Tect System for Pool Enclosures
PRO-TECT Fastener Protection System consists of a nylon sleeve and a cap that, together, cover and protect the anchor screw. The PRO-TECT nylon sleeve gives protection from electrolysis, providing worry-free installation while extending the life of the product. This is very important for the harsh conditions of the coastal environments and extreme temperatures.
The PRO-TECT cap snaps onto the top of the nylon sleeve, covering the head of the Blue-Tap anchor screw. Due to its special design, the cap will not come off easily. Caps are available in White and Bronze.
By repelling water and preventing penetration, PRO-TECT reduces or eliminates the need for warranty work, increasing life expectancy of the structures. -
Read MoreQuick ViewT-Nuts
T-nuts are barrel shaped fasteners with internal threading, and are used to provide an anchor point for a bolt in a piece of wood, whether a flat board or a dimensional piece. They are especially useful when a flush surface is wanted. T-nuts have a flat base with prongs bent up at 90° angles, parallel to the barrel. After pre-drilling a hole, the t-nut can be fixed in place either by tightening a bolt into it from the top, which pulls the prongs into the wood, or using hammer to pound the locking prongs into the wood until flush.
-
Quick ViewElite Beam Clamp
Elite Beam Clamps are used as structural attachments to the top or bottom of metal beams, purlins, channel, or angle iron.
-
Hot
Quick ViewOriginal Wej-It® Wedge Anchors
The Wej-It original Wedge Anchors are time tested with proven reliabilty and has been an industry standard for over 60 years.
