Plastic Anchor Kit
This kit contains standard drywall/concrete expansion anchors, screws, and a masonry drill bit sized appropriately.
Kits are available with standard Phillips pan head screws, or with slotted hex head washer screws.
Sizes are:
3/16″ Anchor & Bit, with #6 – #8 x 3/4″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Slot Hex Head Screw
- Additional information
- Description
Additional information
| Size | #6 – #8 x 3/4″ Phillips Pan Head Screw, #10 – #12 x 1″ Phillips Pan Head Screw, #10 – #12 x 1″ Slot Hex Washer Screw |
|---|
This kit contains standard drywall/concrete expansion anchors, screws, and a masonry drill bit sized appropriately.
Kits are available with standard Phillips pan head screws, or with slotted hex head washer screws.
Related Products
-
Read MoreQuick ViewAnchor Setting Tool Powder Load, .22 Caliber
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .22 caliber powder loads provide the force needed to drive those fasteners into place. This level is the lightest available, for smaller fasteners and thinner materials.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick ViewAnchor Setting Tool Powder Load, 25 Caliber Disc
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .25 caliber powder loads provide the force needed to drive those fasteners into place. This level is the medium strength available, for average fasteners and materials.
Each disc has 10 powder loads, and there are 10 discs per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Quick ViewPegatanke Cold-Welding Epoxy, Clear
PEGETANKE® Transparent, is a high quality epoxy adhesive, designed for those jobs where no traces of adhesive use should be left, giving a more esthetic finish. PEGETANKE® Transparent is the only one in its kind with high resistance to tension and high temperatures.
EXCELLENT FOR:- Goggles
- Headlights
- Translucent materials
- Glass
-
Read MoreQuick ViewToggle Bolt, Zinc Plated
The Toggle Bolt is a spring wing type hollow wall anchor designed for use in block, wallboard and other hollow base materials. The Toggle Bolt is a two-part assembly consisting of a machine screw and a spring wing toggle. Sizes range from 1/8″ x 2″ to 1/2″ x 6″ with combo round, flat, mushroom, tie-wire or slotted hex head styles.
-
Read MoreQuick ViewLead Wood Screw Anchor
Lead wood screw anchors, also known as lead wood screw shields, are ideally suited for projects that require fastening wood or anchoring brick, concrete, block or softer masonry. You’ll find these anchors install easily as the lead alloy material is soft enough to use, yet hard enough to provide strong holding power. A pre-drilled hole is required for installation.
We do not recommend for ceiling applications. -
Read MoreQuick ViewHollow Wall Anchor, Long and Short
The sleeve type hollow wall anchor is designed for use in base materials such as plaster, wallboard, concrete block, hollow tile or plywood. It is installed using a drill and can be used with various wall thicknesses. The sections of the sleeve expand as the screw is tightened and driven into the wall. The front section of the hollow wall anchor will add permanent screw threads, so that once set, the screw may be removed as often as necessary without affecting the anchor.
These anchors are also known as Molly bolts. -
Read MoreQuick ViewBlue Plastic Anchor, w/Lip
This is a standard plastic expansion anchor that can be used in drywall or solid walls for light hanging or attaching needs.
-
Quick ViewHammer Drive Tool
Drive pin anchors are installed in pre-drilled holes. Using this tool and a hammer, a solid strike drives a nail into the anchor body, expanding the anchor to form a tight fit. These anchors secure light loads to masonry materials.
-
Read MoreQuick ViewRamset Fastening Pins
The Ramset Fastening System Drive Pins are powder actuated pins used to attach material to concrete or steel. The pins are specifically fabricated for toughness and durability.
The 1/2″ and 5/8″ pins are knurled for extra grip, and are specifically engineered for use in structural-quality steel.
The 3/4″ and 1″ pins are perfect for attaching metal track to concrete.
The 1″ up to 2″ pins are sized for attaching furring strips or plywood to concrete.
The 2-1/2″ and 3″ pins are designed to attach 2×4’s to concrete. -
Read MoreQuick ViewAnchor Setting Tool Powder Load Strips
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These color coordinated .25 and .27 caliber powder loads provide the force needed to drive those fasteners into place. They provide from medium power up to the highest power of loads available.
Each strip has 10 powder loads, and there are 10 strips per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator’s manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders.
