Lead Hammer Drive Anchor
The Hammer-Set anchor is a mechanical drive anchor consisting of a zinc die cast expansion body and zinc plated steel expander drive pin. Hammer-Set anchors are medium-duty anchors designed for a variety of fastening applications in concrete, block, and brick. It is ideal for light-duty and tamper-resistant applications. Use Hammer-Set anchors to attach termination bars, drywall track, electrical boxes and clips, flashing, lumber and more.
- Additional information
- Description
- Features
- Loads & Dimensions Chart
Additional information
| Sizes | 3/16″ x 7/8″, 1/4″ x 3/4″, 1/4″ x 1″, 1/4″ x 1-1/4″, 1/4″ x 1-1/2″, 1/4″ x 2″, 3/16″ x 1″ Nylon, 1/4″ x 1″ Nylon |
|---|
The Hammer-Set anchor is a mechanical drive anchor consisting of a zinc die cast expansion body and zinc plated steel expander drive pin. Hammer-Set anchors are medium-duty anchors designed for a variety of fastening applications in concrete, block, and brick. Use Hammer-Set anchors to attach termination bars, drywall track, electrical boxes and clips, flashing, lumber and more.
- Works in concrete, block, and brick
- Great for fastening electric boxes, conduit clips, roof flashing, plywood and 2 x lumber
- Fast, easy installation
- Install through material to be fastened
- Ideal for light-duty and tamper-resistant applications
- Low profile mushroom head
- For indoor and outdoor use
- Not for use in overhead applications
Related Products
-
Read MoreQuick ViewRamset Washer Pin Fastening Systems
Designed to drive flush into steel and concrete
Consistent and optimum quality in every pin
Washer increases bearing surface against material -
Read MoreQuick ViewNylon Round Head Nail-In
-
Read MoreQuick View
Lag Shield, Long and Short
The Lag Shield is a screw style anchor designed for use with lag bolts. It is suitable for use in concrete and the mortar joints of block or brick walls. In harder masonry materials, short style Lag Shields are used to reduce drilling time. The long style version is used in soft or weak masonry to better develop strength. The Lag Shield is not recommended for overhead or life safety applications.
-
Read MoreQuick View
Anchor Setting Tool Powder Load, .22 Caliber
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .22 caliber powder loads provide the force needed to drive those fasteners into place. This level is the lightest available, for smaller fasteners and thinner materials.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Quick View
Pegatanke Cold-Welding Epoxy, Clear
PEGETANKE® Transparent, is a high quality epoxy adhesive, designed for those jobs where no traces of adhesive use should be left, giving a more esthetic finish. PEGETANKE® Transparent is the only one in its kind with high resistance to tension and high temperatures.
EXCELLENT FOR:- Goggles
- Headlights
- Translucent materials
- Glass
-
Read MoreQuick View
Grey Plastic Anchor, No Lip
This is a standard plastic expansion anchor that can be used in drywall or solid walls for light hanging or attaching needs. This type has no outer ring or lip that remains outside the pre-drilled hole, so there will not be any plastic visible once the screw is in place. Also, whatever is being attached to the wall will sit directly against the wall, with no gap.
-
Quick View
Hammer Drive Tool
Drive pin anchors are installed in pre-drilled holes. Using this tool and a hammer, a solid strike drives a nail into the anchor body, expanding the anchor to form a tight fit. These anchors secure light loads to masonry materials.
-
Read MoreQuick View
Ramset Fastening Pins
The Ramset Fastening System Drive Pins are powder actuated pins used to attach material to concrete or steel. The pins are specifically fabricated for toughness and durability.
The 1/2″ and 5/8″ pins are knurled for extra grip, and are specifically engineered for use in structural-quality steel.
The 3/4″ and 1″ pins are perfect for attaching metal track to concrete.
The 1″ up to 2″ pins are sized for attaching furring strips or plywood to concrete.
The 2-1/2″ and 3″ pins are designed to attach 2×4’s to concrete. -
Quick View
1″ Conduit Clip w/Pin
Designed for use with Powder Actuated tools, this EMT clip will secure conduit to concrete, without the need to drill a hole first.
-
Read MoreQuick View
Blue Plastic Anchor, w/Lip
This is a standard plastic expansion anchor that can be used in drywall or solid walls for light hanging or attaching needs.
