C6+ Ceramic Epoxy, Max Strength
For The Most Demanding Jobs Red Head C6+ is the highest strength adhesive in our history. Designed for use in the most demanding anchoring applications, the maximum strength of Red Head C6+ is backed by ICC-ES approvals for both concrete and masonry. It is also the only adhesive approved for core-drilled holes in cracked concrete without the use of a roughening tool.
C6+ Epoxy is available in 15oz and 30oz sizes.
- Additional information
- Description
- Data Charts
- Data Sheets & Downloads
Additional information
| Size | 15 Oz., 30 Oz. |
|---|
Red Head C6+ is the highest strength adhesive in our history. Designed for use in the most demanding anchoring applications, the maximum strength of Red Head C6+ is backed by ICC-ES approvals for both concrete and masonry. It is also the only adhesive approved for core-drilled holes in cracked concrete without the use of a roughening tool.
C6+ Epoxy is available in 15oz and 30oz sizes.
- At least 25% stronger than the old C6+ formulation for threaded rod in cracked concrete with seismic conditions
- Fastest Cure time in its class, curing in just 2.75 hours at 90°F and in only 2 hours at 110°F!
- ICC-ES approved for cracked concrete and seismic applications (ICC-ES ESR 4046)
- ICC-ES approved for masonry applications (ICC-ES ESR 4109)
- ICC-ES Approved for use in core-drill holes, even in cracked concrete
- At least 10 minutes of nozzle life (10 min working time at 110F)
- Can be used down to 40°F and up to 110°F
- Can be used in oversized holes
- Rugged cartridges resist breakage due to rough handling or cold temperatures
- 24-month shelf life
- 2:1 Mix Ratio
Related Products
-
Read MoreQuick ViewLead Wood Screw Anchor
Lead wood screw anchors, also known as lead wood screw shields, are ideally suited for projects that require fastening wood or anchoring brick, concrete, block or softer masonry. You’ll find these anchors install easily as the lead alloy material is soft enough to use, yet hard enough to provide strong holding power. A pre-drilled hole is required for installation.
We do not recommend for ceiling applications. -
Quick View1/2″ Combo Bit for 1/4″ Lead M/S Anchor
This 1/2″ combo drill bit installs lead anchors for 1/4″-20 combo sidewalk bolts. I works for all masonry surfaces, both block and concrete. The smaller pilot bit starts the hole in the right location, and the larger 1/2″ step bit drills the perfect hole for setting lead machine screw anchors.
Fully adjustable collar allows you to set the depth of the hole for a perfect set every-time. Comes with Hex Wrench. -
Read MoreQuick View
Anchor Setting Tool Powder Load, .22 Caliber
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These .22 caliber powder loads provide the force needed to drive those fasteners into place. This level is the lightest available, for smaller fasteners and thinner materials.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator's manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick View
Ramset Washer Pin Fastening Systems
Designed to drive flush into steel and concrete
Consistent and optimum quality in every pin
Washer increases bearing surface against material -
Quick View
Pegatanke Cold-Welding Epoxy, Black
It is a high quality epoxy glue, developed to withstand the most demanding physical and chemical conditions. Used in industrial, automotive, naval, electrical and construction repairs; as well as in the simplest home repairs, thanks to its high resistance to extreme temperatures and voltage.
EXCELLENT FOR:- Petrol tanks
- Water tanks
- Radiators
- Car repairs
-
Read MoreQuick View
Threaded Stud
Threaded studs are available in a variety of thread and shank lengths for use in concrete, some types of concrete block, and A36 or A572 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required or for suspending sprinkler systems.
The threaded studs have a specially designed point to allow proper penetration into the base material. A plastic flute is mounted over the point to retain the drive pin in the fasteners guide of the tool providing guidance during the driving operation. A plastic cap is also provided to protect the threads of the fastener during the driving process as well as providing guidance during installation. -
Read MoreQuick View
Nylon Round Head Nail-In
-
HotQuick View
Original Wej-It® Wedge Anchors
The Wej-It original Wedge Anchors are time tested with proven reliabilty and has been an industry standard for over 60 years.
-
Quick View
1-1/4″ Ceiling Clip Assembly
The Ramset Ceiling Clip is designed to mount into a slanted ceiling, with hanging wire attached through the eye. Able to support light loads such as suspended ceiling grids.
-
Read MoreQuick View
Knurled Track Pin
The Ramset 3/4 in. Drive Pins are ideal for fastening track in concrete and can be used to penetrate dense concrete and structural-quality steel. The pins are specifically fabricated for toughness and durability.
