BA-4-16 Clip T-Bar
The BA-4-16 tee and T-bar fasteners are used to suspend or mount electrical boxes, lighting, signage, fan and more to acoustical tees, troffer and t-bar.
- Description
The BA-4-16 tee and T-bar fasteners are used to suspend or mount electrical boxes, lighting, signage, fan and more to acoustical tees, troffer and t-bar.
Related Products
-
Quick View3-Hole Corner Angle L Bracket
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 2-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Quick View2-Hole Corner Angle L Bracket B
This connector is used for connecting metal struts together, as a 90° angle. The two sides are 2″ and 1-7/8″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance. -
Quick View
Elite Copper Loop Hanger
Elite Copper Loop Hangers are required for hanging copper pipe and allows for vertical adjustment of pipe after installation.
-
Read MoreQuick View
Caddy 1-Hole Strap for Conduit
The CPVC One Hole Wrap Around Pipe Strap is designed to support pipe running horizontally on side of a beam, or as a guide to mount CPVC pipe running perpendicular across the top of a beam, or on a vertical run. Model 1070 may be installed onto wood using supplied fastener, or into minimum 20 gauge steel using one 1/4″ x 1 tek screw.
-
Quick View
Elite Beam Clamp
Elite Beam Clamps are used as structural attachments to the top or bottom of metal beams, purlins, channel, or angle iron.
-
Quick View
3-Hole Corner Angle L Bracket, Stainless
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 2-1/2″ long, with three 9/16″ holes to secure to struts or other surfaces. Stainless steel material makes this product more rust resistant, and it is suitable for exterior uses where rain or salt water are expected.
-
Quick View
4-Hole Corner Angle L Bracket, Stainless
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 4-1/8″ long, with three 9/16″ holes to secure to struts or other surfaces. Stainless steel material makes this product more rust resistant, and it is suitable for exterior uses where rain or salt water are expected.
-
Read MoreQuick View
Gasket, Ring, Red Rubber
These gaskets are comprised of red rubber, a copolymer of Styrene and Butadiene, also known as SBR. It feature excellent impact and tensile strength, good resistance to abrasion and easily conforms to uneven flange surfaces.
This Synthetic material was developed as an alternative to Natural Rubber. The red rubber gaskets are recommended for service in cold and hot water, air, steam,and some weak acids. It should not be used with strong acids, oils, grease, and chlorates -
Quick View
Elite Clevis Hanger
A clevis hanger consists of one U-shaped clevis and a second V-shaped clevis with a hole in a flattened section at the base of the V, joined together with a bolt. Clevis hangers are used as a pipe attachment providing vertical adjustment for pipes
-
Quick View
2-Hole Closed 45 Degree Angle Connector
This connector is used for connecting metal struts together, at a 45° angle. The two sides are 3-1/2″ and 2-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
