Blue Plastic Anchor, w/Lip
This is a standard plastic expansion anchor that can be used in drywall or solid walls for light hanging or attaching needs.
- Additional information
- Description
Additional information
| Size | #4 – #6, #6 – #8, #6 – #8 Bulk, #10 – #12 Bulk, #14 – #16 |
|---|
This is a standard plastic screw anchor that can be used in drywall or solid walls for light hanging or attaching needs.
Related Products
-
Quick ViewHammer Drive Tool
Drive pin anchors are installed in pre-drilled holes. Using this tool and a hammer, a solid strike drives a nail into the anchor body, expanding the anchor to form a tight fit. These anchors secure light loads to masonry materials.
-
Quick View1-1/4″ Ceiling Clip Assembly
The Ramset Ceiling Clip is designed to mount into a slanted ceiling, with hanging wire attached through the eye. Able to support light loads such as suspended ceiling grids.
-
Read MoreQuick View
Anchor Setting Tool Powder Load Strips
Powder actuated tools are the quickest, most efficient way to set fasteners into concrete slabs and block walls. These color coordinated .25 and .27 caliber powder loads provide the force needed to drive those fasteners into place. They provide from medium power up to the highest power of loads available.
Each strip has 10 powder loads, and there are 10 strips per box.
Caution: Always test-fasten with the lowest power level for your tool. If more power is necessary, use the next highest power level until proper level and fastening is achieved. Refer to operator’s manual for more specific details. Observe all safety reminders. Tool operators must be trained and qualified as required by federal law. Failure to use properly can result in serious injury or death to users or bystanders. -
Read MoreQuick View
Plastic Anchor Kit
This kit contains standard drywall/concrete expansion anchors, screws, and a masonry drill bit sized appropriately.
Kits are available with standard Phillips pan head screws, or with slotted hex head washer screws.
Sizes are:
3/16″ Anchor & Bit, with #6 – #8 x 3/4″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Phillips Pan Head Screw
1/4″ Anchor & Bit, with #10 – #12 x 1″ Slot Hex Head Screw -
Quick View
Pegatanke Cold-Welding Epoxy, Clear
PEGETANKE® Transparent, is a high quality epoxy adhesive, designed for those jobs where no traces of adhesive use should be left, giving a more esthetic finish. PEGETANKE® Transparent is the only one in its kind with high resistance to tension and high temperatures.
EXCELLENT FOR:- Goggles
- Headlights
- Translucent materials
- Glass
-
Read MoreQuick View
Ramset Washer Pin Fastening Systems
Designed to drive flush into steel and concrete
Consistent and optimum quality in every pin
Washer increases bearing surface against material -
Read MoreQuick View
E-Z Anchor Drywall Anchors
The E-Z Ancor is a one-piece self-drilling anchor designed for optimal holding performance in drywall. Because it pre-drills its own small precise hole, no hole preparation is necessary.
With a range of choices, including mini, regular and heavy duty, and available in zinc or nylon, there is an E-Z solution to your hanging problems. -
Read MoreQuick View
Knurled Track Pin
The Ramset 3/4 in. Drive Pins are ideal for fastening track in concrete and can be used to penetrate dense concrete and structural-quality steel. The pins are specifically fabricated for toughness and durability.
-
Read MoreQuick View
Threaded Stud
Threaded studs are available in a variety of thread and shank lengths for use in concrete, some types of concrete block, and A36 or A572 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required or for suspending sprinkler systems.
The threaded studs have a specially designed point to allow proper penetration into the base material. A plastic flute is mounted over the point to retain the drive pin in the fasteners guide of the tool providing guidance during the driving operation. A plastic cap is also provided to protect the threads of the fastener during the driving process as well as providing guidance during installation. -
Read MoreQuick View
Pipe Spike
Powers Pipe SPIKE® is ideal for ceiling applications where hanging threaded rod is needed.
The SPIKE® anchor is a patented, one-piece, tamper-proof vibration resistant anchor for use in concrete, block, brick or stone. Several head styles and anchor materials are available. The SPIKE® anchor is formed with an “s” shaped configuration at the working end of the anchor to create an expansion mechanism. Since the anchor is pre-expanded, there is no secondary tightening operation required which greatly reduces the overall cost of an anchor installation.
