BH9 Jack Chain #12 X 100′
The BH9 jack chain, when paired with the #11 S-hooks, is commonly used for hanging industrial class fluorescent lighting fixtures. It is electroplated for basic rust protection.
- Description
The BH9 jack chain, when paired with the #11 S-hooks, is commonly used for hanging industrial class fluorescent lighting fixtures. It is electroplated for basic rust protection.
Related Products
-
Standard Riser Clamps (6400)
Model 6400 Standard Riser Clamps from Elite components are designed for copper tube sizes. They are available in carbon steel with Copper colored Epoxy (PC) and in sizes from 1/2″ thru 4″.Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8) -
Read MoreQuick ViewPost Bases for 1-5/8″ Strut
These three models of a post base provide a secure mounting point for strut. Once properly bolted in place, it is guaranteed not to move. And with six bolt holes on three sides for all models, the strut will be held in place with no chance of slipping out.
Options include having a square base plate, held in place with four bolts (10 hole models), or a smaller rectangular base held down by two bolts (8 hole model). In addition, the 10 hole model can have the strut and plate square to each other, or having the plate at a 45° angle. These various configurations are meant to accommodate your specific needs. -
4-Hole Corner Angle L Bracket
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 4-1/8″ and 3-1/2″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
Read MoreQuick ViewCaddy Two-Hole Strap for CPVC Pipe
Caddy 2-Hole Strap helps with the installation of CPVC pipe on wood, masonry or other surface when extra load bearing is needed. Its curved shape positively snaps onto the pipe, making installation easier. For indoor or outdoor applications.
-
4-Hole Corner Angle L Bracket, Stainless
This connector is used for connecting metal struts together, at a 90° angle. The two sides are 3-1/2″ and 4-1/8″ long, with three 9/16″ holes to secure to struts or other surfaces. Stainless steel material makes this product more rust resistant, and it is suitable for exterior uses where rain or salt water are expected.
-
2-Hole Corner Angle L Bracket A
This connector is used for connecting metal struts together, as a 90° angle. The two sides are 2-1/4″ and 1-5/8″ long, with a 9/16″ hole to secure to struts or other surfaces. An electro-galvanized coating provides rust resistance.
-
4-Hole Closed 45 Degree Angle Connector
This connector is used for connecting metal struts together, at a 45° angle. The two sides are 3-1/2″ and 4-1/8″ long, with four 9/16″ holes to secure it to struts, or other surfaces. An electro-galvanized coating provides rust resistance.
-
Read MoreQuick ViewCaddy Stand-Off Strap, 2-Hole for Conduit
Two-hole stand-off straps are used for mounting CPVC pipe to a wall, ceiling, or other surface. They eliminate the need for wood blocks under the pipe. They position the pipe 1-1/2″ off the surface.
-
Read MoreQuick ViewCaddy 1-Hole Strap for Conduit
The CPVC One Hole Wrap Around Pipe Strap is designed to support pipe running horizontally on side of a beam, or as a guide to mount CPVC pipe running perpendicular across the top of a beam, or on a vertical run. Model 1070 may be installed onto wood using supplied fastener, or into minimum 20 gauge steel using one 1/4″ x 1 tek screw.
-
Standard Riser Clamps (6200-6300)
Model 6200-6300 Standard Riser Clamps from Elite components are designed for standard iron pipe. They are available in either galvanized or plain and in sizes from 1/2″ thru 24″.
Compares with federal specifications A-A-1192A (Type 8) and ANSI/SP-69 and SP-58 (Type 8)








